Search results for query: *

  1. A

    440 intake manifold good ?

  3. A

    440 intake manifold good ?

    I have a 440 edelbrock performer intake manifold on my build street build with holley sniper efi is the performer fine or should I step it up to the rpm intake manifold
  4. A

    Lifter bore bad casting ?

    O Ok awesome thanks for the info
  5. A

    Lifter bore bad casting ?

    No Nothing laying around I agree with you maybe the machine shop
  6. A

    Lifter bore bad casting ?

    Looking at my 440 motor and noticed. Casting around lifter looks like it chipped away has anyone seen this also is ok ?
  8. A

    440 oil pan dimples filler ?

    This windage tray has two rubber seals on both sides but says it's for flat surface oil pans
  9. A

    440 oil pan dimples filler ?

  10. A

    440 oil pan dimples filler ?

    It's one of them gasket tray combos with rubber seal
  11. A

    440 oil pan dimples filler ?

    What can I fill the dimples on my 440 pan with so I can use a mr gasket windage tray with rubber gasket ?
  12. A

    Anyone run a holley sniper yet ?

    Is the inline pump loud ?
  14. A

    Anyone run a holley sniper yet ?

    Purchased a holley sniper will be installing in a month or two if you have any advice let me know intank fuel pump ? Or inline
  15. A

    What hp are mopar 440 stock main bolts good for

    What kit are you guys using for studs ?
  16. A

    What hp are mopar 440 stock main bolts good for

    500 to 600 hp it's easy and cheap enough I should just do it for insurance I guess
  17. A

    What hp are mopar 440 stock main bolts good for

    When is it necessary to install arp studs in the 440 lower end mains building mild street 440 will stock bolts hold up ?
  18. A

    Oiling vs non oiling pushrod

    They are not stock rockers 1.6 prws with ball to ball
  20. A

    Oiling vs non oiling pushrod

    I'm actually using prws roller rockers they came out very nice actually
  21. A

    Oiling vs non oiling pushrod

    Ok and how are you restricting.them ?
  22. A

    Oiling vs non oiling pushrod

    Looking for pushrods for my 440 build need to be 9.150 long ball to ball I've found tons of oiling push rods but none non oiling I can see my luniti lifters have oil hole but I know mapar uses the shaft mount system for oiling will I see any issues if I get oiling pushrods is my question
  23. A

    440 oil pump ?

    What is suggested for the 500 hp range for oil pumps is the standard melling oil pump fine or do I need a high volume I have a 440 with a hemi 6qt pan
  24. A

    [FOR SALE] Wanted driveshaft

    Looking for mopar drive shaft 45 5/8 center to center 7290 u joint or 7260 let me know what you have
  26. A

    Adjustable roller rockers speedmaster vs prw

    440 with flat top kb pistons edelbrock 75cc heads ported polished luniti 513lift cam would like to do 1.6 rocker arm ratoo to up the lift a little bit and yes I need new pushrod as week but won't know what size untill I get rockers
  27. A

    Adjustable roller rockers speedmaster vs prw

    Looking for stainless roller rockers was looking into prw but than saw speed master for alot cheaper but they look the same anyone use either of these ?
  28. A

    Aluminum heads and steel shim gaskets ?

    Are you talking about the 1009 gasket ? Did you spray with copper as Well?
  29. A

    Aluminum heads and steel shim gaskets ?

    Ok thank you i will look into mls gaskets
  30. A

    Aluminum heads and steel shim gaskets ?

    I have a 440 I'm installing e street heads on 75cc chambers was wondering if I can use the smaller .20 steel shim gaskets on aluminum
  32. A

    Aluminum heads and steel shim gaskets ?

    I have a 440 I'm installing e street heads on 75cc chambers was wondering if I could use the smaller .20 shim gaskets on aluminum heads ?
  33. A

    is the procharger still for sale ?

    is the procharger still for sale ?
Back
Top