Search results for query: *

It's on the intake of my 76 400, there's also a 4 pin and a 2 pin ballast resistor on the car. Just trying to clear some junk off the firewall.

My horn doesn't work, I've tested it across a battery and it works fine, i've cleaned where it grounds to the body, the violet wire on the 4 pin relay is hot. The car has a grant gt steering wheel, i pulled the horn push out and there's no wires, so i pull the steering wheel off and the wire...

How much ign Timing does a 360 Magnum like, the motor is 98-03, don't know much about the internals, it's got a 650 DP, single plane intake, roller rockers. Mick

Just bought a 73 Duster, it has both the rear cables and the front, so i'm assuming I need two intermediate cables and all the connectors,rods etc. Does anyone have an illustration and who does the best price for these parts. I was going to rob the bits off my 69 dart race car but it's...

Why do some mopars have a 3 pin and others have 4 ?

I keep getting an error message when I try to contact people through craigslist, is it stop foreign scammers ? It's definitely something they've just introduced because I bought a car off there a couple of months ago. Mick

I need the wiper linkage rods and clips for a 73 duster and i have some off my 69 Dart, just wondered if they would fit ? Mick

I need the linkage rods and clips for a 73 duster, also i need a washer bottle, and the jets as well please. Mike

I've just pulled the timing set off my 360 and there's no cam number at the front, all the BB Cams i've used had the number stamped on the end. Mick

My 7-1/4 has quite a badly worn ring and pinion but i know where there's a better one very cheap but its 4 inch pcd and mine's 4.5, just wondered if my ends would swap over. Mike

Car is mild 360, headers intake and 4 barrel, just wondered if i need to show any of the transfer slot. Mike

Someone i know has got an 8.25 for sale and i was hoping to pull my 7.25 out and stick it in my 73 Duster. Mike

Been sorting electrics on Duster but still haven't got the dash lights working, all fuses are now good, any ideas ?

Bought this a few months ago, 73 Duster 340 clone, has a 360 in it, headers, edelbrock intake and edelbrock carb. I've not been well this last few months so just got started on it, the throttle was only opening half way due to the kick down linkage, i need to set that, the rear lights...

Just wondered if they will fit without rubbing ? springs are in stock location, stock wheel tubs as well. Mick

I've just bought a 73 Duster with no blower fan but i've a 69 one i took out of my Dart racecar, just wondered if it will fit ? Mike

Does anyone know this car, thinking of taking a punt on it ? Mike 1970 Plymouth Duster 340

$550 for all.

I have a good condition trim panel off my car that i was thinking about selling to pay for some fresh parts on the car, what would an honest valuation be for this ? Mick

I'm looking to fit fibreglass doors on my Dart and would appreciate any tips and pics for ideas. Mick

Couple of weeks ago i ran a small pb et and speed, despite the track not hooking very well, went 10.14 132.88 with a poor 1.47 60 ft. Earlier in the day they prepped the track for a supercharged altered, i ran straight after and managed a best 60ft of 1.36 but over revved the car in second gear...

Went to our annual mopar event in England the other week, not the fastest track over here but ran my fastest time at this particular track, a 10.20 at 131.67 in 75 degree weather but a tail wind. Also ran a couple of 1.40 60ft's back to back. I am taking it to a quicker track in a few weeks...

Has anyone got one of these, it's to go to Modesto CA. Mike

I've just reamed my spindles out for tubular upper control arms and unfortunately, the reamer went a bit off line, will this cause a steering issue. Mick

Took my Dart out sunday with rebuilt motor, decided to time it at the track. Car ran quite a lot slower than expected. Timing was way off, i suspect the dist drive needs knocking back a tooth. The car ran ok but ran on a little when switched off, also it was lighting the carb up at times...

I just scored a set of 6 cyl torsion bars for my 440 Dart, my 60fts were useless last year so looking to improve. Over the winter I've changed my none adjustable shocks for CE 3 ways up front and rancho 9 ways out the back, i've also changed the TA "J" convertor for a 8" Dynamic with 5000...

Took my Dart out to test and tune sunday, could'nt get the poxy ratchet to shift correctly and i'm worried about overheating my freshly rebuilt trans, anyway i'm looking at a new click shifter, shortlist is either cheetah scs, ppp kwik shift 2 or quarter stick. Would like some opinions please...