Search results for query: *

Evening all, Curious if anyone has used the intake solenoid block off kit for their 392 in an Abody. I'm in the early stages of putting together an upcoming 392 swap and this appears to be one of the issues with fitment against the firewall. Ideally I would like to leave the firewall as is but...

Good evening all, up until recently I have been planning on upgrading my 340 4speed to a 416 stroker and aftermarket 5 or 6 speed transmission. With that said until recently... I found a couple 392 Hemis with 6 speed for a relatively if not less cost than the 416 approach. I have not spent...

Good evening all, I recently finished installing a 4 wheel brake kit on my 71 Duster so I could have the 5x4.5" bolt pattern. Fronts are the typical 73' style but rears are the MBM setup. The car previously had the manual brake Kelsey Hayes front but drums on the rear . As expected the master...

Hi all, I am selling (1) ESR 18" wheel that has the 5x4" small bolt pattern. I bought this wheel to install on my car but I found a complete 5x4.5" conversion kit instead. Wheel was $250 with the custom bolt pattern drilled so it would be a great template for someone. It's just collecting dust...

Good morning all, curious if anyone from Grand Rapids / West Michigan had any recommended shops to align my Duster. Place I used in the past is gone and a few that I called said they had an old mopar in there once a few years back... Either way if there is someone in town that's knowledgeable...

Good afternoon all, I am looking at upgrading my alternator due and wanted to know the alternator output at idle of the Tuff Stuff 130 amp single wire. Are there other factory appearing units out there anyone recommends? Tuff Stuff Performance High-Amp Output Factory Cast-Plus Alternators 9509CSP

Evening all, I was looking at parts the other day and came across a few LD340 intakes for sale for $799 and they claim it was because of the Chrysler part number... if that's the case I'll post mine for sale as it has the Chy# as well (attached photos). Anyways, curious more than anything on why...

Repairable hood for sale that fits a 70-72 Plymouth Duster. Bought it to repair but found a six pack fiberglass hood soon after that I used instead. $50 obo

Good evening all. I'm replacing my water pump as my previous failed and started leaking. I know there are "performance" pumps out there to help flow at idle and prevent cavitation at high rpm for $100+. At rockauto I found the following two pumps that have the same improved impeller but for half...

With longterm plans of installing 18" wheels I have to finally upgrade the brakes to the large bolt pattern. Once complete I'll pick up the wheels and upload some pictures. In the meantime along with the front brakes I reinforced the lower control arms, upgraded to the PST torsion bars, Hellwig...

Good evening all, I'm in the process of upgrading to the 4.5" bolt pattern but plan on keeping my 71 k member. With that being said are there recommended sway bar kits that will help provide more clearance? I know the 73 k member is preferred but I wanted to see what options I have first...

Question for everyone... can the 73+ lower ball joint be installed on the 67-72 kelsey hayes sbp brakes? Thanks in advance

Hi all. This year I would like to start the process of converting my Duster from the 5x4" pattern to the 73 and up 5x4.5". Currently need front spindles and brackets along with rear axles and rear brakes. Let me know what you have. I appreciate the help in advance.

i know this may spark some opinions but I’m looking at which option the majority of mopar peers recommend. I’ve had my H code 71 Duster on the road for 10 years now and am looking at taking the next step in performance. It’s a 4-speed car with 3.23s and my best quarter mile time of 13.4 sec...

*hub assembly*. Autocorrect got me again I have an old pair of small bolt pattern spindles and hub/rotor assembly and would like to get rid of these. I purchased these 8 years back but found another complete set that I used on my car instead. Initially asking $100 but name your price and we can...

hi all, I found the wheel I will be purchasing that is available as a 17x7 4.25" backspace and 17x8 4.5" backspace. They say silt will bolt on and go by I would like some first hand feedback. What do you guys run for wheels/dimensions and alao any recommended tire sizes? This is a stock...

Hi all, I have a couple extra fenders for sale. These have the recessed marker light for the early dusters. Both will need a decent amount of work but doable. Asking $75 each obo. Located in Lowell MI, east of Grand Rapids 20 minuets or so.

hi all, I came across this company recently that makes a nice selection of 17" wheels with the 5x4" bolt pattern. Before I go much further has anyone purchased wheels from this place? Reviews, Pictures, and wheel dimensions would be helpful as well. http://www.americanlegendwheels.com/wheels/

Good evening all, Its looking like my tires wont last all season like id hoped..... im looking at the MT Sportsman S/R tires and wanted to see if anyone is running these on their A-body. if you can provide pictures and tire size that would be awesome!!!

Good evening all. I've had this sitting on my shelf for a few years now and figured I would try it out this spring on the 340. It needs a good cleanup as it's pretty filthy and wondered what you recommend to clean/seal to keep clean. The LD340 I have on the car was virtually brand new when I...

hey all. I've been to mopar nationals a few times now and looking at other events to mix it up a bit. Any of you attend the monster mopar weekend in Norwalk Ohio? The cross state mopar drive is the most intriguing with this one. Anyways any feedback would be appreciated.

I figured I would pass this along. I installed the Truck-Lite 27270C last year and will NEVER go back. I do a lot of driving at night time and these lights work better than my Saab HIDs. Anyways, since I purchased my lights last year a few more options have hit the market. Take a look at the video.

Now that a decent number of members have purchased a FiTech unit I thought it would be nice to have a common thread where we could discuss specific tuning / adjustments that we have made along the way. Yes this unit is pretty darn close out of the box but I think all of us have made some...

Anyone heard of or purchased exhaust pipes from this site? Mandrel Bent Pipes Looks like they offer the complete exhaust from manifolds to tips in mandrel bent configuration. I will be giving them a shout on pricing.

Hi all, I recently went to efi on my 340 and no longer need my current fuel system. I purchased this kit in June of 2014. It's the Mallory 140 pump with return style pressure regulator. The system worked out great for my duster as I used this with 3/8" fuel line and an 850 thermoquad. Since I...

Hi all, Has anyone had luck with replacing the OE fuel sending unit with a new version that does not disrupt the dash gauge? I tried one a few years back and my fuel gauge was not accurate anymore. Anyways looking at a 3/8" unit but any input would be appreciated.

What an improvement!!!! I replaced my halogen Sylvania Silverstars (which actually worked pretty good) with these Truck-Lite led headlights. Amazed by the increased visibility in distance, width, light quality across the board. Highly recommend these to you guys. I picked mine up on eBay with...

I finally found a six pack good last fall and was able to fix it up these past few weeks. Overall it looks pretty good but I was more interested in the fresh air for the 340. All I have to do now is add the 340 wedge decal on the hood and install the air cleaner plate to seal the hood. Looking...

Well im just about sold. I am looking forward on seeing more people install this system as my plan is to go this route in the spring... Finally someone isnt gouging the market for efi @ $995 for the system excluding fuel pump. FiTech Dual Quad Shelby - YouTube

Good evening all, My 71 340 has an older points style distributor but with the Mallory electronic module. It has worked well but the bushings are getting tired and it needs to be rebuilt. Would I see any improvements in engine operation by upgrading to the mopar electronic setup? It seems to...