Search results for query: *

ok, i have heard how horrible the torker 340 intake is. ii have one, but do not have a stock one. is the torker any improvement over stock,, or is it about the same just a little lighter?

that's as in cranck and piston/rod choice!!!!!!!!! i am putting the numbers correct engine back into the fc7 dart, but am looking for ballz out of it, without going extreme. i am not looking for any huge h.p numbers, but yet a unknown figure more than the normal 340s' i have had. all were...

ok, i have a 340 that has a hairline crackin cylinder number 2. is this block toast, or can it be sleeve? who with first hand knowledge can give me any info. , so any help would be appreiated any one know where to get a sleeve? what do they go for? about what shoould it cost at machine shop?

anyone know off hand what the torque spec are for a 340 rod bolt? thanks

ok, i thought at first this was the stock 340 intake, but it looks to sit so high. i pulled the heads off the 340, and they seem to be ported? they do match the gaskets that i took off. cab you tell me what the advantage i will gain from running this intake and heads over a set of j- heads i...

ok, i had the 340 running great before taking the engine out. pulled the distributor so i did not damage it during the yank out. lost position of said mark. so, i set cyl 1 at tdc, and the rotor faces the number one cyl. what do i have wrong? is that correct. and one have a link to the...

ok. the volare was running great. now when i turn the key to start it, it starts right up, but as i let go of the key, it shuts right back off. seems like it is losing spark......? any ideas?

i got 72 duster. 340-4 speed. mild built engine. 14" tires, 3:55 gears. i eed an exact number it will run in the 1/4. OH, AND I WILL BE LEAVING THE LINE HARD. i will winde it to 6 grand and just dump the clutch if i have to, just to gain .0001 seconds!.. sorry, rant is over wow, i love...

is there a easy way to see whether i have a solid or hydraulic cam? it has the mopar peformance 1.5 rocker setup. also, how close to the head can the pushrods be? mine are aweful close, if not touching. i hear a rattle when running, and pulled the v.c, put the number one cylinder to where...

i am dropping in my 340-4 speed setup into my duster, but what is easier? to put engine in first? headers in place first? do i put starter on before engine goes in? can someone tell me the process for the simpiliest install

i am looking to buy a complete 340 six-pak setup, but i thought i remember something about offset push rods.? for what was the reason of them being off set? i do not have much time to search, so i figured i would just ask.lol

ok, i have a 340 engine going in a 72 duster with a 318 k-member in it. i have a set of solid motor mounts that were on a 340, in a 340 k-frame. i have a set of shumacer /6 to 340 mounts. will any of these sets work to put a 340 in the 318 k-frame, or do i have to buy yet another set...

ok, fisrt set says 360 on them, under the valve cover. and the last three digits is 974. what are these off of? thay look to have 202 valves. second set last three digits are 302. are these the swirl port heads? both sets have been magnufluxed and checked for cracks, but then sat...

I HAVE A 69 340 THAT THE FIRST THINGS PUNCHED ON THE FRONT NEAR THE HEAD IS FW, and i am wondering what numbers should be on the front? and how many numbers/letter should be in a row? thanks

i am putting a 340 in a /6 scamp. it has the biscuit style mounts. where do i order these from? anyone have a used set to sell? anyone have a link to a specific place to order them? thanks

ok. i have a 70 340. it had 12 to 1 pistons, and i had them cut down. they will now be about 10.2 to 1. have a old school holley strip dominator intake. holley 750 carb. going with 3:55 gears. do not know if i am going 4 speed or staying with the auto for now. i will be running headers. not...

can anyone help me figure out what brand pistons these are? they have number 90825 on the dome. and right below it, it says .030 so i know it is 30 over, but cannot find anything on what brand they may be. the second pic, i took to show how far out of the bore they are

is this suppodes to be factory? the 340 in the dart has solid lifters with adjustable rockers?

i just landed a shizz load of mopar goodies, and was also invited to grab a 6/12/70 340 engine with. it is just the shortblock. it has pistons, rods, and crank. it had a oil pan, but no intake. it has sat outside for over 15 years. i pulled a rod cap, and there is still oil on the bearings. i...

i got a 318 that the build date is 11/18/69... i cannot see any writing on the damper that says it is cast. what year did they change? what is this engine h.p rating? what is the best crank 318 out there?

ok, maybe all you gear heads can point me in the right direction. i am taking a fellow members' advice and keeping the 72 340 that is in my 70 34 4 speed car. i am looking to push about 400 hp out of her. what would be my best options to do? i really do not want to stroke it. if you could...

i have 2 72 340 engines, and i am wanting to know what has to be changed in them to make the same horsepower as a like 68-70 340? one i have has j heads on it, and i have a friend that knows how to port, so he will be doing the port and polish on my heads for me. i am wanting to get about...

i started the car and let it run for a little bit, to find out that there is antifreeze dripping pretty good out of the back header bolt on the driver side. is there anything i can do?????????????????? i do not want to have to take headers out. please someone shed some light on this problem

hey guys, i am picking up a 73 340 duster that is the original engine in it. i am wondering all the differences in the enge compared to the older year 340's i know it has lower compression and smaller valves. are the exaust manifolds the better flowing ones? same as the older 340's? i...