Search results for query: *

Never really had them sitting next to each other but would a 318/904 converter be the same as a 225/904 converter or are the totally different and I should punch myself in the face for even thinking about it? Note.....wasn't my idea but a buddy said that they may be the same, I kinda...

Well Santa Ross is bringing me a 8 1/4 for the dart so I will be swapping out the 7 1/4 that I just swapped in pretty soon. I will need shock plates for a 8.25 but I also need the measurements for a driveshaft in a 73 dart custom (4 door) slantsix/904/8.25. We should put together some sort...

904, with the tranny in park is the lever on the transmission all the way forward or all the way back?

Anyone running a A500 in anything behind an older (nonmagnum) smallblock? Im getting the motor and tranny from my dads 95 Dakota for free when he swaps in the 2001 360. The motor is a 95 318 that has a bad oil pump and was starting to knock a little this weekend and the tranny has been rebuilt...

I know a couple of you have doen it. What shifter did you use, did you chop it up so it would fit? I was looking at either the B&M Hammer or the QuickSilver shifters but should I get the stock one and not use the plastic housing or should I get a console shifter even though they are listed for...

What all is needed to mate a 518 up o a 360? The block and crank are from 1976. What flexplate, converter and what year tranny should I look for? I found this on ebay if it makes a differance...

I have searched all over this and other sites and I cant find the diagram that shows the differant leghnths and mounting areas of the mopar auto tannys. The one that is just an outline of a tranny with all the measurememts for 904/727/518. Anyone have it?

Will the tail shaft housing on a V8 904 interchange with a slant six 904? They look to be the same and are bolth just under 15 inches, The slant in the car dosent have the little mounts for the console shifter and the V8 one I have dose.

Would there be any big problem that you can think of with installing a welded in drain plug in the bottom of the housing? Not the very bottom but the bottom of the smooth part on the back, just to make it a little less messy when removing the 3rd member.

Ok after getting screwed on one "rebuilt" 727 on craigs list I have a hardcore mopar buddy that said that his tranny guy will rebuild mine if I supply the rebuild kit and a case of beer. I was wonderring what you guys think of the kit I found on this page... It is the first kit under the...

I picked up a B-body 8 3/4, 54 incher with backing plates and breaks but no axles or 3rd member for 50 bucks at the monroe swapmeet. All I would have to do to drop it in my 73 scamp would be change the U bolts and shock plate and spread the springs 1/4 inch on each side right? How much...

I got the new (rebuilt a year ago and just sat on a shelf until this weekend) 727 in and made up some new fluid lines to the cooler. Now Im trying to get the lokar cable fine tunned, the cable was on the old tranny for about 2 months so Im pretty sure that all the streach is out of it. My 1-2...

Is there a way to get the old seal out without dropping the pan and valve body? I replaced the smaller seal that is in the kickdown rod but my leak is the bigger seal that is counter sunk in the case. The tranny is in the car so I am working with limited space and I really really really dont...

What is the stock stall speed for a 360/727 out of a car? Not counting the converter how much fluid will it take to fill it with a stock pan? What are the measurements for the 2 tailshafts (short and long). What are the stock shift points, 1-2 = 10-15 mph, 2-3 = 25-30 mph ? Can you...

I want to adjust the kickdown band on my 727 tonite but I dont have a in-lb torque wrench all I have is a ft-lb wrench. The book says 41 in-lbs for the adjustment but my wrench only goes down to 10 ft-lbs and Im pretty sure that 41 in-lbs = about 3 1/2 ft-lbs. Can I tighten it to 10 ft-lbs and...

I got the one peice kickdown rod along with the throttle cable bracket with the little L shapped extender bracket off a 80's? dodge truck today all for 5 bucks at a local yard. Im looking to replace the 3 peice kickdown thats on the car now, I have a lokar kickdown cable but was trying to save...

Has anyone gotten one or know someone that has one? Any bad experiences with TCI? Im thinking about getting a 727 Sizzler for my 73 scamp.

Will the valvebody from a 904 work in a 727 if they are bolt smallblock trannys from the early to mid 70's?