Search results for query: *

Well, I sent her a little too hard during my last track visit. I think I may have found the coolant leak source but, I’m not 100% sure. You all see anything I may have missed?

This Dodge 318 was in the junkyard earlier this year. After being plucked from the yard and overhauled on a 5 year old’s budget, it’s out here at the drag strip collecting wins and leaving people scratching their heads.

It’s been a busy summer. I built this little 318 for the 3k drag challenge and was pretty impressed by it. It had sat in a junkyard for a decade before I picked it up. I just had to see what it ran on the Dyno. With these power levels and a 9.47sec pass in the 1/8 (with no tune and dragging...

So I was cruising on the hwy at about 60 mi/h when I noticed the engine pitch start to change. I immediately looked at my gauges and noticed that my oil pressure dropped from 30 psi to 0. My temp was still the same. I pulled over, popped the hood and checked the oil. Still full and clean as far...

So I've delayed asking for help for awhile now but, with one day left, I need help. About a month ago my bcuda just decided it wouldn't start. So I went through some tests and sure enough, no spark. I popped my dizzy cap off and found both centri adv springs had popped off and were stuck to the...

So I attempted to fire up my 360 for the first time yesterday. It started just fine but then died about 10 seconds later. Then I notice that there was a coolant leak coming from the aft part of the intake manifold. The leak was so bad that when I poured coolant in the radiator it started to pour...

Is the starter gear suppose to sit flush with the flywheel or back a quarter inch like it is now?

Alright, well after 3.5 years, my 68 barracuda is a couple weeks away from hitting the road. My problem is that I'm running short on time (about to be shipped out in a couple months) and I need help with pushrod lengths. I was wondering if anyone has a similar setup and if so, could you please...

Hey guys so I purchased the Howard hydraulic roller lifter set for my 91' 360 from Summit. I'm also running the comp cams 280HR extreme energy cam. Upon installing my lifters, I realized that the stock skeleton frame/lifter retainer does not fit with the upgraded lifters. Is this a big deal? Do...

What is the groove in between the bearing and the crankshaft seal? Everyone I've asked hasn't had a clue.

Hey so I just purchased my edelbrock aluminum heads and I realized that I ordered the heads set up for a flat tappet cam. The springs are set to 128 ft-lbs. I have a 91 roller block. I guess edelbrock sells a head setup for a roller cam. Anyways, will my heads still work?

Alright well after two and a half years into the bcuda I am drawing close to the finish line. I have completely finished the body and paint(never will I start with a body that bad haha), and I have pretty much finished the short block. My next buy is going to be the cam. I have a 92 roller LA...

Alright well like the title says, a good friend has a 318 without spark. It died on him as he pulled out of the parking lot. I know this because I pulled out a spark plug and grounded it to a bold as he turned it over (nothin). We just replaced the coil (old one was beat up and dented) and there...

So what do you guys think? Is this company legit? has anyone bought these rods from Ebay and had any issues? just curious because Im in the market for h-beams however, Im in a mopar kind of budget and would like to get them for a good price. heres the link...

Alright so I have a 91 roller 360 block that I am now blueprinting. I am looking for about 450-500 crank HP (75% street/25% strip). Because of my budget I am going to have to use my stock 308 heads for a few months(dont want to settle with a weak bottom end). The cam I pick needs to be able to...

If its not one thing its another right? Well I drove the truck about 40 miles today without a problem. Once I get back home the truck begins to shake. Then the engine light pops on. It feels like its not balanced. I checked the harmonic balancer and its fine(rubber seal in the balancer went out...

Ok, I know it is not an A-body but I figured being a 360ci you guys could help me. So Im having a problem with my 96 Ram 1500. I was driving down the road when the engine died. I pulled over to the side of the road and tried to start it up again, no luck. I then pulled a spark plug and checked...

Ok, so there is a71' 340 block that has been bored .040 and honed. It also comes withnew freeze plugs and Ross forged pistons. The guy is asking 900 bucks for both. What do you guys think these are worth? iS 900 a good deal? what do you think I should offer him? Thanks. Oh, and what should I pay...

So ive notice a change in the way my 68 fastback fish has been running. Its taking a very long time to warm up and sounds like a cylinder isnt firing properly. So I decided to install some new spark plugs hoping that it was just a fouled plug. When I was removing the plugs on the passenger side...

sorry for the dumb question but I just want to make sure that my information is correct. Edelbrock aluminum heads for sbm will fit on any small block right? so if I buy the heads for my 340 I can install them on my 318 for now and then swap them back onto the 340 when I get closer to finishing...

Hey how many miles would a properly built 416 stroker( all forged bottom end) last? It seems like a lot of money for an engine that may not last that long. Anyone have any high mileage strokers?

Hey guys after researching all over the web and this site ive decided that it would benefit alot of people (including myself) if people would be so kind as to post their "medium" built small block combos. By medium built im talking about maybe cast internals, rhs/X heads instead of eddies...