Search results for query: *

Question what is measurement on a 30 over 360 piston ? Is it 4.030 ? Or is the 4.030 the bore size for the piston ???

I have 2 cranks from 360 4027169 with cfd cast into it and a 3418640 . Are both crank the same or is one better ? I'm planing on building a 78 year block and want the better one of the two

I picked up a 85 360 tore it down and notice 6 rods had 2899496 pressed pin and 2rods cylinder 3and5 had 3418645 pressed pins also is this right or have someone been in this block ? Crank number 20277169 , block number 4179930-360-2 , could some one help me , the 6 rods showing they are 340...

I have a 360 block I used a digital caliper on piston bore , reading I got was 4.035 is this in specs of being 30 over ?? Thanks

I picked up a 360 block and crank dispose to be 30 over bore is the piston hole should it be 4.030 when measureing it ? Also is the walls bad it have lines running in it , I can't feel them hand not groves in walls

i got my 360 done, it is a 78 model four barrel motor ,im running a hughes whiplash cam 504/515 with matching springs ,locks retainers,and lifters, i installed comp pushrods. the motor have the self adjusting rockers arm with shaft. (factory) . the motor started right up and sound decent other...

78 360 four barrel motor, 596 head casting smog holes pluged off, double roller timing chain , hughes whiplash cam 504 intake / 515 exhaust with 1.5 rockers matching springs,locks,retainers, alum dual plane intake, my trany is 727 with tci breakaway converter, what size carb should i use with...

i have a 78 360 with 727 trany , the motor is external balance , i have a tci breakaway stall converter i want to install to this setup, being external balance do i need to change the flex plate or buy weights to weld to converter ,i notice factory converter have a weigh add to it. if i need to...

i have a 68 valiant with a 273, im planing on droping a 360 in its place my question is can i use the 273 motor mounts and brackets on the 360 ? whould i have to buy sertain mounts ?

i have a 78 heavy duty 360 four barrel and 727 trany came out of an rv with 52,000 miles. i drove rv befor pulling motor and run good, i now have motor pulled apart to install new gaskets and paint. motor have the 596 smog heads i have already pluged off the holes. this is going into a 68...

i have a 68 valiant with 273 will the oil pan work on a 78 360 ? i went to jegs and they gave me a pan for 72-89 center sump #555-50272, my car is center sump also, will the one for 72-89 work ? im buying parts for the switch over for this winter and dont want the pan i bought sitting around...

would a 68 273 timing cover and water pump work on a 80 360 ??? does any one know ? thanks

i got a 80 model 360 im putting in a 68 valiant what alt brackets ,pulleys and power steering bracket do i need so i dont have to use the a/c compressor , any one have any pictures so i can get the idea of what im looking for ?? will my 273 items work ? and do a 273 and 360 use the same water...

i just pulled a 360 four barrel motor and trany out of a 1980 rv with 54,000 miles what is the electrical plug on the trany for ? its by the shifting linkage.. sorry for no pictures. also under hood it says heavy duty 360 whats heavy duty about it ? it does have the 596 heads on it.

i think its time to pull the 273 out of my 68 valiant, my brother have 2 360s one is a 2 barrel the other is a 4 barrel both are 1981 motors the four barrel is in a rv. should i grab up on the four barrel motor for my build and also would the trany that is in the rv work in my valiant or use...