Search results for query: *

My 727 is toasted. Rear drum is cracked. I have a donor transmission mid 70s. The rear drum looks the same as mine but has 3 holes drilled into it. Are 727 parts interchangeable?

727 with external cooler. Going to 3000 stahl and manual valve body. Am I going to need a deep pan?

I've got 4.10 gears in my scamp I'm over 3000rpm at high way speeds is this going to hurt anything?

No reverse today. Noticed when I first backed it out seemed sluggish in reverse. Brought it home played around with it and nothing at all. Fluid good all other gears seem fine. I'm not even getting a rpm drop when going to reverse. 727 trans rebuilt. Aftermarket shifter, I did wiggle shifter...

What are yall using for automatic shifters? I have a Hurst Quarter stick and im not really liking it. Seems like its a two handed operation and more of a pain in the butt to operate.

Ive got a hurst quarter stick. Ive played around with adjustment. I cant seem to get it to catch Park all the time. The instructions say to adjust with both trans and shifter in Neutral. Just curious if someone could walk me though how they adjust theirs? Maybe im missing something. Do you...

I've had a small issue with the bolts that hold the backing plates coming loose and leaking. Do y'all use loctite here?

Whats best method of removing an axle shaft? I was just watching you tube vid where a guy used his drum backwards like a slide hammer. Any other options?

My axles are aftermarket but they dont have the hole in them to line up with the backing plate nuts. Would drilling one be an option here? Can barely get a wrench on them and not enough room for socket and properly torque them.

Should say Dana 60! Just about ready to get my perches welded. Curious as to how thick the dana 60 tube walls are? Ive googled and seen .250 and .313 but nothing definitive! I was going to set my pinion and tack them and have it welded but If its 1/4" or more my little welder isnt up to that...

Are they any benefits to running these on the street? Been looking at http://www.summitracing.com/parts/tac-17675/overview/. Ive heard about the low band apply and this has that. How exactly does one work? Shifting manually I know at stops can you stop in 3rd then down shift back to first?

My scamp build I did the rebuild on the trans my first attempt at anything like that. This was done about 2yrs or so ago. Hasnt had fluid in it since just this weekend. Today went out and a puddle looks to be coming from front of trans front seal or pump gasket. Any chance its dry and will seal...

So today my flexplate to converter bolts finally showed up. I went out to put them in and they dont line up. I can get one in but after the the rest are just a bit off. I tried leaving the one bolt slightly loose as to be able to move the converter a bit but that didnt help. Any suggestions...

Rear Suspension is SS springs, CE shocks. Dana 60. Ive read many write ups and all them are different including the tech pages on BBD. I imagin I need to set pinion angle before measuring driveshaft length correct? What should pinion angle be? Also I have a 440, 727 and Dana 60. If ive read...

Lets see those trans coolers where ya got them mounted. Radiator doesnt have cooler provisions so I have an external. Im concerned it may not be big enough and also where yall got yours mounted. Thanks!

Ok I got some photos here that Is what I think how these go together. Is there to be a gasket on the back side of the backing plate where it sits flush with the axle flange? Also do I want to put some axle grease around the bearings? Are you suppose to grease the splines where they go into the...

Ok, I have a Dana 60 housing sitting thats been cut down to what I assume is the proper length. I sent the off a set of Moser standard 8 3/4 axles off to Moser to get cut and resplined. They keep telling me my numbers dont add up dispite me measuring several times and getting the same numbers...

I bought this some time back. Wondered if anyone could ID it. Its a 727 converter and the guy list some info. But didnt know the brand? He said he thought it was a Coan but wasn't sure. http://s667.photobucket.com/albums/vv39/eaglesguy1981j/?action=view&current=converter.jpg

Can anyone tell me how much of the spline on the axle engauges with the carrier? I had my rear shortened and I have stock A body length Moser axles. There is quite a bit of meat on the splines just wondering how much actually engauges with the rear? Dana 60 if that makes a difference

Ok I got a problem. I can not get the tail housing on. I got the snap right spread and putting it on straight. Am I missing something? Also when I go to put it on it seems like it goes down over the bearing but seems like the tail housing wants to twist out of aligned straight.

I have to say Im reading the directions and im lost. Anyone have any good videos or know any good tech articles? Being honest this looks out of my relm.

72ScampTramp submitted a new Article: How to install a Bolt In Sprag in a 727 Read more about this article here...

72ScampTramp submitted a new Article: How to install a Bolt In Sprag in a 727 Read more about this article here...

Has anyone used this sprag from TCI http://www.tciauto.com/tc/727-bolt-in-sprag-unit.html

Rear ends done and looking to move on to the trans. I'm looking at some performance rebuild kits. I like kits because they make things easy on me when buying. Im thinking the first kit has the parts I need. This is a performance trans. Behind a Mild 440. Which one of these would you choose? Im...

Ok I just got my Dana 60 narrowed. Its 50 5/8ths right now. The builder gave me dimensions to have the axles cut 23 7/8ths for Driver and 21 7/16 for pass side. Does this sound right? I thought the 2 sides were only 1 3/8ths difference? Im a bit confused....

Ok the bolts that hold the backing plates on. Were can I find a source for them? Also is there a gasket or anything between the ends and backing plates? Does anyone have a exploded view on assemble of this area?

What do yall use that holds up well? Looking to paint my rear and get it ready. Looking for something that holds up well... Spray bomb.

Ok Im tearing down my Dana today for rebuild. Is there anything I need to watch out for? Whats a good way to clean all these parts up?

Ok after setting my wheels and tires in and measuring backspace to backspace I came up with 50 5/8ths. Now this is about ¾” of clearance from the tire to the frame rail is this enough? I’m trying to get as much on the outside as I can to prevent rubbing. Tire size is 28x13.5 MT ET...