What’s your favorite carb for a 360?

[doopdoop67]

I am wondering what Carburetors you guys like? I’m running an edlebrock avs2 right now and I like it but I’m wondering if it’s too small for my 360 with an edlebrock top end package. Probably just needs some more tuning.

 

[xLURKxDOGx]

You like to **** around with them or not? If you do then holley its where its at. Ive learned to like the holleys more these days but a good edelbrock 750 will do the job if you dont like messing around.

Jake

I am wondering what Carburetors you guys like? I’m running an edlebrock avs2 right now and I like it but I’m wondering if it’s too small for my 360 with an edlebrock top end package. Probably just needs some more tuning.

 

[70aarcuda]

my choice holley 750 dp.

 

[318willrun]

my choice holley 750 dp.

I 2nd this ^^^ 4779 Holley DP

 

[66fs]

TQ

 

[mderoy340]

650dp street, 750dp street/strip

 

[Syleng1]

Thermo Quad. Pre 72.

 

[mopowers]

650dp street, 750dp street/strip

Nuff said

 

[krazykuda]

I love the Holley 80457 600 vacuum secondary electric choke for my small blocks... Been running them for decades with great performance and reliability...

Holley 4160 Aluminum Street Carburetor

 

[70aarcuda]

Lets see...brand new Holley 750 DP....or a Thermoflush that has not been made in almost 40 yrs...LOL.....

 

[Johnny Dart]

I am wondering what Carburetors you guys like? I’m running an edlebrock avs2 right now and I like it but I’m wondering if it’s too small for my 360 with an edlebrock top end package. Probably just needs some more tuning.

AVS2 what ?

 

[doopdoop67]

AVS2 what ?

I have a eldebrock avs2 650 cfm electric choke

 

[273]

Install a vacuum gauge and see what it reads on a full throttle run to see if there's room for gain.

 

[lemondana]

The TQ hasn't been made in nearly 40 years but there are still new ones out there. I have 5 NOS early ones. I used 1 of the new ones on my Polara in my avatar on the 440. It works flawlessly, always starts, and NO vapor lock. And -NO I didn't have to rebuild it. I installed directly out of the Carter box, adjusted a little bit and I haven't touched it in 10,000 miles.

Lets see...brand new Holley 750 DP....or a Thermoflush that has not been made in almost 40 yrs...LOL.....

 

[RustyRatRod]

Put this on it.

 

[66fs]

Lets see...brand new Holley 750 DP....or a Thermoflush that has not been made in almost 40 yrs...LOL.....

Any carb can be rebuilt. TQ will give better power and mpg especially with an auto trans. I would not have a "fix it constantly Holley" on a street car. LOL

 

[DARTLARRY]

What about the new Demon carbs? They look like a TQ, and can even get resin bowl as well.

 

[66fs]

What about the new Demon carbs? They look like a TQ, and can even get resin bowl as well.

I like the way they look but am just getting ready to try one.

 

[DARTLARRY]

My brother has one on a 440, it runs really well.

 

[Johnny Dart]

I have a eldebrock avs2 650 cfm electric choke

Perfect carb for a 360.
When you make the move to a Holley, I'll buy the Ede.

 

[j par]

Only one carburetor...???

 

[ir3333]

Well....we need to know your engine specs and how you are using your car?
If it's a warm 360 and you only drive it on the street it's pretty hard to beat
600 Edelbrock!

 

[j par]

I think there's a lot to be said for the Holley Street Demon. It's relatively inexpensive and works very much like an Edelbrock with probably a little better throttle response and probably a little better acceleration..

 

[66fs]

What about the new Demon carbs? They look like a TQ, and can even get resin bowl as well.

It has a lot of features of the TQ, but it is the standard Carter/Holley bore pattern. It even uses standard TQ floats, so you can pitch the plastic ones and use brass floats.

 

[DARTLARRY]

we put one a 440, and it ran great with minimal work.