Search results for query: *

Before I tear into my cluster can anyone tell me if this is most likely cable related or Speedo gears(cluster) related? 1972 Dodge Dart

72 Dart Swinger 340 4 speed with factory discs up front For quite sometime I have had a strange knock that I feel through the steering wheel. I have a very radical motor so I'm used to it jumping around a bit( occasional header bang etc..) With that said I have constantly kept an eye on my...

340/ 4speed 833 NOT a diaphram pressure plate. This trans is my Achilles Heel! I have had this trans in and out several times for one reason or another. It is completely rebuilt, new clutch, new pressure plate ( Hayes) from Brewers. Everytime I mess with this trans something always changes...

Just looking for some tips before I pull the steering wheel. Whats the most common problem here with the horn ring?

I have purchased two covers now and they never fit my 72 Dart Swinger. They swear they do when I order it, but I have to stretch and pull to get them on and then it only goes halfway down the side of the car. Can anyone out there recomend a decent cover that actually fits? Thanks:banghead:

1972 Dart (Swinger). I have relocated the springs inboard and I'm interested what combos and back spacing folks are running with this set up. It's time to purchase some wheels. Thanks.

Who makes a decent fuel sending unit?I am at work and I need to order one and forgot to measure the output size. I believe they offer 5/16 or 3/8s. What is most common size?

I would really like to find a hood Tach. Are there any decent aftermarket hood tachs out there????

I have a nicely worked set of 360 heads with 2.02 valves lying around and thought I would install them on my trucks 318. I am having the 318 rebuilt and thought I could save some money by not having to have the heads done. So I am only doing this swap to save some bucks. The 318 is a 1987 block...

69 340, 72, Bell Housing, 833 Trans Changed my clutch and pressure plate to a McCloud (3 finger style) the clutch I had before was a heavy duty racing pressure plate and really was a work out on the street, but everything worked fine. After replacing the clutch I could not get it to release...

Brewers sent me a series 100 11"clutch for my 340/ 425 hp small block. This is the stock replacement clutch I believe # 260121. Is this clutch strong enough for that much power??? Also they sent me the pressure plate 11" 360156. The 3/8 bolts do not fit through the pressure plate holes. Anybody...

I have a 340 with 12:5:1 comp street car. What are the opinions about 100 octane gas ? Do you think it is sufficient? We have a couple of ststions in our area that sell 100 and 108 octane fuel and I have been experimenting with mixtures etc... I have run this motor a few times on 93 pump gas and...

The Caliper bolts/Pins on my a body stick out almost an inch to far when they are tight. They measure about 5 inches long from under the bolt head to the end. It seems I need some that are around 4-1/8 long. I can not find them anywhere. These are the bolts that the caliper slides the pads back...

I have a fiberglass 6 pack hood and need to design a plenum for it. I could use some ideas'/ or under hood pics for referance.

I need to pull my trans and put a new clutch in. I would like this to be the last time I have to do it for a while. I have a 340 4 speed. How do you determine if the fly wheel needs to be replaced? How often when replacing the clutch would you need to replace the flywheel?

Is there a reputable vendor that rebuilds 8-3/4 rears?

Did Darts only come with the small wheel bolt pattern?

I noticed, while driving yesterday, that my steering seemed to develop a dead spot in it. Meaning I have to rotate the wheel a good 8 inches or so in the opposite direction before the steering becomes positive again. Almost like something is loose and the wheel is not turning the linkage until...

Can anyone ID this odd rocker arm I found on a 340?

I need a Fan shroud for my 72 Dart. 22" Rad.

I have a shroud but it is really faded. Looking for tips on a paint or dye to make it look nice. What did you use????

1967 273 V8 86,000 miles for sale. It is a running motor and just came out of my Fathers 67 Coronet. Also have the K frame for sale as well. $350 for the motor $50 for the K frame.

I put a Fiberglass 6 pack hood on my Dart and noticed that my aircleaner is very hot to the touch. has anyone noticed these hoods creating a heat pocket in the engine bay? I thought, with all that air being forced in there that things would be cooler rather than hotter. Anybody experience this?

Just got the car together and now I am working out all the bugs. I was curious as to how much whine is normal for these 8-3/4 rear ends? I have a rebuilt a body 8-3/4 742 with 3:91 gears with a 4 speed man. I have a very slight whine when I am slowing down that i notice. Is this normal for a...

I am currently trying to fit wheels for my 72 dart Swinger and I dont seem to be able to fit the same size rims and BS as other folks. i am wondering if this can be due to the type of drums I have. can someone educate me on the different sizes they made? I have a 8 inch rim with 4.5 back spacing...

I am having clutch adjustment issues because the arm on the Zbar is hitting the starter and or header. i believe this to be the wrong Zbar for an A body unless it is a six cylinder Zbar. Can anyone tell me what bar this is? Thanks [

Do you have to remove the trans to locate the casting numbers?

First car resto so Im learning as I go. hard braking and hard acceleration seem to starve the car for gas. Floats? Is there a way to adjust this?

Know of a vendor that sells chrysler, dogde and plymouth key blanks? thanks folks

Any body have to re-route their rear pipes due to a spring relocation? Pics would be great. Trying to figure the best way to do this.