Search results for query: *

I have mild build 318 on my Duster. KB pistons for compression, about 9.4 lunati voodoo cam, 256/262, lift .454/.475 performer intake, 600 cfm vacuum secondary carb. And headders and 2 1/2 dual exhaust. 904 trans and 2500 stall. Basically now i have stock 318 heads, stock valve size. Would...

I finally figured were most of the wind noise is coming. Its not leaking windows it is that small groove between crome list and roof. I tested it by putting masking tape and closing that groove, 70 mi/h and no wind noise. So has anyone noticed this and any ideas how to remove that groove.

I was interested about how hot these under hood open air elements get on normal drive so i made little experiment. I put normal air temp inside one and drove my car about one hour. Hottest it got was 97f while outside was about 60. That 70 is inside car. So if its about 30-40f hotter that would...

Hi I am trying to install auxilary transmission cooler to my 72 904. Because here all fittings are metric its hard to find correct fittings. What size are stock 904 cooler fittings?

Last winter i rebuilded my 318. KB 167, about 9.5 comp, lunati 10200701 cam .454/.475, summit 600cfm carb, home porting on heads, valve job... runs nice and still gets decent mileage, 18mpg rear gears are 3,23. This winter its time to rebuild transmission. planing to install tf 2...

So after all thinking, ordering parts and machining parts I finally have everything to start rebuild my 318. You can read my rebuild plans etc in this tread: http://www.forabodiesonly.com/mopar/showthread.php?t=244352&page=4&highlight=rebuild So far its going great, i will try pictures later...

went and replaced my broken speedo cable and i noticed it didnt go straight to trans, instead it went to this small thing. this was located bit under of brake booster on driver side inner fender. There is one black wire. My car has 318 904 a/c ps pb stock gauges So whats this part?

Hi i a going to rebuild mine 1972 stock 318 from plymouth duster next winter. I havent done engine rebuild so this will be mine first. what i have now: stock 318 exept edel performer intake, summit 600cfm carb, hooker headers (bad), 2 1/4 dual exhaust and hei ign. rear is 8 1/4 sg 3.21...

Hi I am going to swap my 904 to a500 to my 72 318 duster. A500 is coming from 91 dodge van with 318. I know that i need to cut crossmember and fabricate new transmission mounts. thats not the broblem, or shortening driveshaft, i have done it already once with my rear swap. But i like...

HI. I am process of removing ac unit from my car, duster 72 318 whit power steering. Not really sure how I have to run belts. Can I just run two belts, one crank, water and PS, that would be like orginal. Second belt would go from crank to alt, it would fit, but is belt turning angle on alt too...

HI Is it common in USA to protect car underside/cavities waxy type of products or undercoat that newer dries (stays sticky)? if you do can y share comments on these products? I have had these stuff in underside and inside cavities of my duster for over 2 years now and its still looks...

I am planning to upgrade my Electronic ignition (orange box) to hei system. So what kind of ignition coil i can use whith hei system? i will be bybassing ballast resistor same time. What are correct ohm values for this system 0.5-1 ohm?

Hi. Does this look ok contact pattern?? 8 1/4 rear whith motive 3.2 gears backlash is 0.01'' , guide says between 0.008 -0.012 is fine shims are 0.04 thick pinion is torqued to 25 inch pounds my only consern is the lower part of the contact pattern is it too clear edge??? sorry...

Hi all. last year i got duster from California shipped to Finland (above the arctic circle). 72 318 motor, 904 gearbox 7 1/4 with 2.7 gears. i cleaned cars underside and floors, put new paint and rust protection to the underside last winter btw car didnt have any rust which was nice :)...

Hi can i use f-body's rear axle in my duster without cutting axels? in mymopar.com there is list of mopar axels and f-body rear is just 1,14'' wider than my 7.25 now if you have pictures a body with f bodys rear can you link them that i can see

Hello. this is my first post in this forum. I Got my 72 duster last winter and i have been driving it this summer. Goes and drives wery well.... But the 7 1/4 rear axle is dying. Now i have been looking bigger rear axle for my car. I live in Finland so i have much less old axels where to...