Search results for query: *

Usually a cam with LSA of 114 will help a lot with EFI.

Race-mart has the pan for 374.15$! Just call summit and have them match their price.

What about the digital MSD 6AL?

I also have a Suzuki Esteem with a bad HG or cracked head. If I remove the rad cap and start the car up, the coolant will come out like a geyser. The coolant also has a strong gas smell. I didn't have any coolant leak externally, no white smoke from the tailpipe and no water in my oil. You can...

I have aero chamber mufflers that dump before the diff, with a 2 1/2 X pipe. They are a bit loud, especially inside the car (putting some tailpipes on this winter), but it's really not that bad. I never got pulled over, but I was going smooth on the gas crossing a police car... My GF told me she...

I had the same issue on my 360 magnum. You can try a new oil pump, maybe a high volume one would help a bit (I gained around 5 psi when hot) and thicker oil, but I bet your bearings are worn out. It took 200 miles before I spun a rod bearing... I was lucky it didn't get more damage

I think I will try the manifold vacuum on my 360 magnum. I played a bit with timing, I se it about 15-17 idle and 34-36 with the mechanical advance. At idle, the engine is a little rough with the vacuum advance connected to the spark vacuum and seemed to run smoother with the timing advanced...

Yes I know pedestal type rockers should be tightened all the way down, but I backed it up to loosen the pushrod, tightened it to 21 ft lbs and it took about half a turn when I got it torqued and pushrod stopped turning at the same time. I think the stock pushrod must be a bit too short, maybe...

Did you mean 0.033'' longer? .33'' is a lot

If I use the 4* retard keyway on the crank, wouldn't that bring me to 111.5*? It would have the same effect has using the offset cam key. I think I will try both to see which method brings me closer to 110 (there might be a slight difference because of manufacturing...) Is 107.5* too advanced...

I degreed in my cam a couple weeks ago and found the intake centerline at 107.5 degrees instead of 110, so I ordered a 2* offset cam key from mr.gasket (987g) to bring it closer to 110 ICL. Since 2* at the cam = 4* at the crank, is this offset cam key bring me to 111.5 ICL or will it move it a...

I have a street avenger 670 on my 97 magnum. Power off the line greatly improved going from a street avenger 770.

My slant six throttle cable broke 50 miles from home. I had no tools with me and didn't want to pay for a tow truck so I removed the spring on the idle screw and cranked it up all the way in, started the car (revved to 4000 rpm) and dropped it in gear. I was able to go 45 mph on the highway...

I have the Crosswind intake on my 360 magnum. One problem I encoutered is the thermostat hole is too big for a stock thermostat. I finally found a subaru thermostat that would fit. The fitting for the bypass is at a 45 degrees angle, which sucks to install the hose. The edelbrock is straight as...

I have a Viper T56 in my 68 dart. I used a transdapt crossmember bolted between the frame connectors. The tranny mount and the shifter are further back on the viper t56, but it still fits with my bench seat. For the torsion bar crossmember, I made a new one using bent tubes cut in half and...

x2 I had a stuck oil pressure regulator on my slant six. I blew up 2 oil filter gasket (and lost all my oil on the road) before I realized what was the cause. I would try another oil pump

I had the same problem with my 360 magnum I bought used; low oil pressure when hot but no rattle. Changed the oil pump to a high volume but it did not cure the low oil pressure. After 200 miles, it started knocking pretty bad on the highway. My buddy towed me back home, I pulled the oil pan to...

Took me 5 hours with no help to swap engines... Pretty easy

Are you running your engine with the lifters bleeding down? Mine seem to pump up pretty quick as soon as I prime it with the drill. I wonder how it will react on startup....

Is it normal for the stock OEM magnum lifters to bleed down at rest? I did not start the engine yet, just primed it with a drill. It takes up the lash with oil pressure but after 2 minutes the stock pedestal rockers are loose. I checked no.1 intake valve it takes almost half a turn to get the...

1.44$ a liter in Montreal, Quebec. That's 5,45$ a gallon!!!

I just degreed my new comp cam p/n 20-746-9 and found the intake centerline to be around 107.5. This cam should be installed at 110. Should I retard it to 111.5 using the other keyway in the crank sprocket (I have a comp double roller timing chain with the adjustable keyways +4 and -4) or leave...

I'm running the stock serpentine on my 360 magnum so I'm using the stock timing cover. It has a triangle shape cast into it on top of the lower sprocket, I guess it serves as the oil slinger.

I just installed the bushing on my 360 magnum. I used a Durabond one (3.99$ from summit) and drove it in with the new shaft with some assembly lube on it. No need to use the tool, it fits perfectly! I guess it comes prefitted...

May sound like a stupid question but: do you hold the stud when torquing down the nut for the main cap using arp studs? In the instructions they say to install the studs hand tight only but would'nt it turn while torquing the nut?

I think there's a diagram with the weight removal (drilling) of a neutral balance flywheel. You would probably need a machine shop to do it for you. I went with the MP flywheel for my 360 magnum with a viper T56 tranny. My clutch is a 10.5 mcleod unit for a camaro and works perfectly.

I got an answer back from comp and they said to use a melonized steel gear. Who sells those? Or can I go with a standard MP hardened shaft? The gear on the cam is cast.

I just ordered a new comp cam for my 360 magnum pn 20-746-9. It's an hydraulic roller. There's no warning that I need to use a bronze gear. Do I need one?

Looks exactly like the edelbrock pump I have for my carbed 360 magnum (I use the stock timing cover and modified the serpentine setup to drive only the Ram alternator and water pump). You can hear it when ignition is on, but it's not too bad (I can't compare, haven't heard any other electric...