Search results for query: *

Awhile back someone messaged me they had steering column isolators for sale, I lost your contact, could you please reply. I'm also looking for turn signal switch and harness for the same, 73 Duster 4 speed.

Where can I find the plastic shims on my steering column bracket, there are 3 that hold the lower bracket support to the dash frame....??? I have a 73 duster.

What are the best sealing intake gaskets in your opinion, I'm not having much luck with cork...

Anyone running E85 fuel have condensation collecting under valve covers excessively? I'm just running breathers on both valve covers, should I be installing an EVAC, or PCV back to intake?

I have a new AJE K Frame with QA1 coil over shocks with a Flaming River manual steering, has anyone else installed one of these? I took it to an alignment shop yetserday and had it aligned, THIS THING STEERS LIKE A TANK, AND I HAVE SEEM TO LOST MY TURNING RADIUS? I do have a Ford 9" spool in...

Just exactly what is suppose to be holding back of seats onto the bottom half, the one on the passenger side will slide off the exposed metal stud that it latches upon, so what keeps it from coming off the stud that it slides upon, I know there was suppose to be something there?

I installed a Ford 9" in my 73 Duster and need to know what I can do for a Pinion Snubber, I'm overseas in Saudi Arabia and need to provide info to the guy working on my car, any info or pics would be greatly appreciated! Thank you!!

After installation of rack and pinion on new K frame, I have steering shaft float coming out of firewall through shaft collar because of lack of fixed steering unit manual, on the old K frame. Has anyone had this problem, well I know you have if you changed, but what do you do to correct it...

What are the best spark plugs for running E85 fuel 416 stroker, naturally aspirated, digital 6al ignition, and rpm performer Edelbrock heads? With 11.8:1 compression

I'm doing an E85 fuel setup on my stroked 340, wanting to know if anyone else has done this yet, and what were your results? I'm running the Holley XP 850, increased lines to 3/8 with an Aeromotive 1000 pump inside fuel cell with pre and post filters. Any tips or tricks I should know about this...

I'm doing an E85 fuel setup on my stroked 340, wanting to know if anyone else has done this yet, and what were your results? I'm running the Holley XP 850, increased lines to 3/8 with an Aeromotive 1000 pump inside fuel cell with pre and post filters.

I just recently built a 340 stroked to 416, flat tappet cam, what is in your opinion to run for break in oil, and afterwards? I was thinking Lucas 20-50 for break in, the Royal Purple 20-50 after that, any advice here would be appreciated! Street car with occasional track runs also.

I'm selling this carb brand new in box because I'm switching to Carb for E85 fuel. 375.00 obo, you pay ride.

Lets hear some facts please, what is best and why? For my reference 416 Stroker TTI Headers and want to run to rear bumper 3" or 2.5" same question, pros or cons? I will be around 625-645 @ Crank on Horsepower.

Can anyone tell me what the difference between a 72 model and a 73 model is, most sites don't even cover 73 models. I have TTI headers on a 340, and putting x pipe on then not sure what mufflers yet..so I looking for recommendations there too!, and then I have put a fuel cell in the trunk to...

I live in SE Ohio (Marietta) postal code 45750, My question is who would you recommend to work and repaint your car, I would be willing to haul car 100 miles to have it done. My past experience is that everyone in my area completely SUCKS! I have a 73 Duster with little to hardly any body work...

I have a freshly ringed and pinion 3:91 sure grip rear end drum to drum out of a 73 duster for sale located in Marietta Ohio $500.00

I have a 73 duster and need to know if anyone has used a ford 9" rear and been able to squeeze 3" pipes up over the rear, stock location on springs. Options .. 1. fuel cell? 2. reduce pipe size though I really don't want too... 416 with 650HP 3. dump in front of rear? Anyone running fuel cells...

pulled my radiator (original) 73 Duster 340 4 speed car with shroud 50.00 plus shipping PM me with your email for pics, having probs posting pictures in this damn Saudi internet, Radiator is in SE Ohio

Pros or Cons? Been thinking about buying one....... for my 1973 Duster 4 speed stroker

I have a set of pretty fresh 318 Swirl Port Heads with less than 500 miles running on them ....250.00 Located in SE Ohio

Eagle or Scat, which is better or preference,, just want some thoughts. Scat is so independent they are not going to be able to get me my crank for 6 weeks, Eagle is in stock, any pros or cons?

I have a Edelbrock Torker 340 manifold, and 600 CFM Carb (1405), only ran 500 miles, going to a different setup now. Im located in SE Ohio, priced to sell first 300.00 bucks takes it. PM me for pictures with your email address please.

I have a complete 73 Duster K frame with torsion bars , upper lowers, disc brakes, the whole front was changed out to AJE unit, everything is good to go 250.00 bucks, you pay shipping. PM me.

1973 340 J Heads, less than 300 miles on them, deciced to go stroker with Elderbrock heads, 400.00 bucks PM me!, also have factory manifolds too 200.00

I have an 8.25 sure grip just freshly rebuilt with new 3:91 Sure Grip drum to drum pulled it out of my 1973 Duster 600.00 PM me if interested

I have 73 duster 340 4 speed I want a new complete frame with brakes, QA1, or AJE, thoughts and opinions by tonight hopefully, or anyone have one for sale?

Anyone, Please help me make a decision, I have a 73 duster 340 4 speed with 3.90 gears, I have some engine issues..pushrods came up through rockers on number 2 and number 8, the engine was just rebuilt 200 miles ago....I assume I have stuck lifters and prob wiped out the new comp cam also...her...

I have a 73 Duster mildly built, A833 4 speed 3:23 rear... my question is what should I go to in the rear for rip snort acceleration, I dont care about going 100mph... this is just a crusier for around town, like I said..not worried about mileage or interstate driving, 3:93 /4:11/4:56 ??? Any...

Will my stock valve covers work with a new Eldebrock Torq 2 intake manifold, and are the rubber gaskets better than cork?, the cork ones seem to seep oil out the tabs.