Search results for query: *

Will these work in a 71 dart swinger with power steering small block 2863553 2863549 and are these the 2 1/4 or 2 1/8

Just did a compression test on my 318 with 90k results are 1-125psi dry 132 wet 2-123dry 134wet 3-114dry 118wet 4- 138dry 153wet 5-134dry 140wet 6-125dry 135wet 7-137dry 138wet 8-136dry 148wet test was performed engine at operating temp all plugs out throttle at wot I checked cylinder 3 twice...

I've got a 71 dart 318 4bbl performer intake electronic ignition 90k on it dual exhaust 3:55 sure grip out back. I wanna pull the trans and have it rebuilt. My question is what would be a good torque converter upgrade for that combo. But I wanna also keep in mind I plan on putting a mild 360 in...

I got American legend streeters , I have drums front and back wheels fit fine. There 17s small bolt pattern. My concern is I get 8 turns by hand til snug on the front. Is that enough ? There 7/16 20 .555 knurl I was gonna get longer ones but cant find them other than stock. I'm sure someone runs...

Does anyone know if someone makes new front hubs for a 71 swinger with 10 inch front brakes

In the process of rebuilding my front suspension on my 71 dart. Was gonna buy new cam bolts. On rock auto they list two different ones theres a 1.05 degree and a 2-1/4 degree. I take it the 1.05 is stock and the other is for more adjustment. I also am putting 17 inch wheels on it the reason I'm...

I'm looking for the metal rod that stops on the latch

I have a 71 dart drums front and back stock suspension in front. I have 8.75 in back a body stock. I'm looking at American legend wheels in a 17 inch I've looked on here but kinda coming up short on a answer as to what backspace and tire size works best for a stock suspension. The bolt pattern...

Ok so I did a timming chain all whent well even drove it awhile til now I'm getting a screaching sound behind the balancer took the belts off and ran it it's for sure behind the balancer my guess oil slinger I know I put it on right anyone ever had this problem

I have the pertronix system in my old points distributor so my ballast is eliminated when I install the mopar setup do I need the ballast if not I have three loose wires instructions say green wire is not used black goes to coil ground and blue to ignition run on ballast where would I route the...

904 with 3:55 with 195/70/14 from what I've seen on a chart it should be a 39 tooth is that correct

I'm in the market 4 a newer truck just looking 4 some reviews if there any good.Theres alotta these 6bangers out there. My current is a 04 ram 5.7 with 229k I like my v8 I'm torn witch ones better.

From what I've read on here I should change my timming chain due to mileage. Any brands to stay away from, recommendations,gotta stock 71 318 88k

Looking to replace my leafs in my 71 swinger as far as I know there stock original with new bushings I installed its gotta 318 with a 8 3/4 I just installed. My question is does anyone have specs on myb bumper height or wheel opening I just wanna see how far off it is from original. I called...

Does anyone know where I can get the small lines that go from rubber to wheel cylinder. I've tried bending them it's just not working out

24th Anniversary Chrysler Performance Trade Show & Parts Swap Meet. Saturday March 2nd 9 a.m.to 5 p.m.sun March 3rd 9 a.m.to 3 p.m. Indiana State Fairgrounds 1202 E. 38th st., Indianapolis, IN 46205 Any one going? Selling stuff?

Could someone tell me if I have the right distribution block dont know year of housing. Brake line kit I ordered doesn't match up. Going in a 71 dart

Anyone got a picture of a cover installed thanks

Looking for a 7260 small yoke 29 spline for a 741 case

I bought a clutch type center for my build is there a way to check if it's good or needs rebuild before it's in the third member or in the car

Looking for a set of usable shock plates

Just looking for input pretty sure I need new brake lines 71 dart all drum with power. New master n booster n front shoes and wheel cylinders how I bought it and who ever put this line on lol.

I'm going to look at a sure grip carrier clutch type how do I know if it is good he's asking a 100$

So I bought this stripe on Ebay found a guy to put it on and this is how they did it I live in northwest Indiana anyone know where I can get it done right close to me and I'm led to believe the stripe I got is not wide enough and where I can purchase one that is right needless to say I'm not happy

Anyone using one of these is it any good

I have a 71 dart where should the level be there is no dipstick and what fluid

I'e got a 4bbl edy n performer intake n petronix ignition what' a good initial timming I'm getting hard start when hot I've put the recommnded carb spacer on it was thinking timming off it' at 10btc now

I wanna install a eddy 9266 do I need gaskets between that spacer

Gonna change 7 1/4 2:76 to 8 3/4 it' a stock 318 4bbl what' a good ratio was thinkn 3:55 anyone know from experience

All right guys I've got the petronix 1 and coil so I bypasse the ballast where is a good spot to wire the electric choke everywhere I check it' less than 12 volts I read on here wiper motor but its 11.18 basically what' a sufficient spot all checks are done with key on