Search results for query: *

Mine is riveted to the driver's fender right about the battery on my 67 Ratfish Fastback.

Thanks Woody for all you did for me on the stainless trim! You a man of your word!

Mike Parting out a rough 69 fast back, it has a fairly nice pair of "green" visors". Would that help? Or PM me.

you still have the moldings mike?

Here is mine, no vert, but hey, it's an A.

Tried to upload another photo, not sure it worked. computer troubles!

Thx Mike. My name is Mike as well and the car has been given to my oldest daughter. (I'm doing the work though!). This fish was bought new in Jacksonville Fl. I know what I'm about to say will get me kicked off the board, but I ditched the 7 1/4 rear and dropped in an 8" Granada rear. It has...

I found this sick fish in a barn about 7 years ago. I pulled it out with a tractor and a chain. It shows 79,500 on the odometer. It still had the certicard under hood where bought new. 273 engine / 904. I have since put in new trunk pan and rear lower quarter patch panels. New shocks, gas tank...

Thanks txstang84 and Ted. Didn't know about the converter size. I will inform my 904 builder to get me a 318 torque converter. As far as the induction choice, I really would like to use my 273, remaned 2 barrel and my exhuast manifolds if possible, for now. I also think I will use the 273 water...

Thanks for all the help guys. I got the engine home and on the stand. It is rebuilt, 30 over, valve job, new water pump and fuel pump 318 (talked to the engine builder),,,BUT I discovered something else. It is not a 1971 318, but a 1978 318 after checking numbers and pulling the vavle covers...

Thanks for info. The 318 engine already has a new water pump and fuel pump bolted on. I was planning on getting a new aluminum radiator as mine is toast. So I can just bolt on my 273 exhaust manifolds and cast iron 2 barrel intake? That is good news! Are you saying I need to use the cast iron...

Hey guys, help this old guy out. I have a nice rebuilt, 30 over, 318. It is just a long block. My 67 Cuda has a 273 2 barrel engine. Will all my brackets for power steering and alternator, starter, etc. fit the 1971 318 engine and are the engine mounts the same? Since I'm asking questions, what...

Thanks Dart, but what is the way to assemble the two piece metal retainers? The longer flat piece, I can see how it goes on, but the smaller piece, does it go on top or where/ thanks for your reply. Also, I have run into another problem on my conversion. Barracuda (67) outer tie rods, big bucks...

How do the retainers go on to hold the calipers on? And, what are those rubber bands for in the kit? Thanks guys, all this stuff was apart when i obtained the swap items. Any pics would be appreciated. (swapping out drums to disc on 67 Barracuda, using 73 Duster disc.)

Okay guys, I hate to ask a question on here that has been beat to death, but I searched and couldn't find what I needed (on brake pedal push rod), so here it is: Going to install a 73 Duster Power Master Cylinder (no booster) with 15/16 bore on my 1967 Barracuda Fastback. Will the existing...

Changing my front brakes to disc on my 67 Barracuda to 73 Duster big bolt pattern. I have everything but new tie rod ends. I need them for the Duster right? I notice the price is a lot higher on Cuda verses the Duster. Both are 9/16" correct? Also, no reason why I can't put the calipers in the...

Thanks guys. I just called Craig at Driveshaft Specialist in Texas and he fixed me up. They are making up what I need for about $28.00 and a few bucks shipping. Mike in Alabama

Thanks schwinger. There is a joint offered on ebay called a Mopar 2 1/8 X 2 5/8 conversion joint. It has the 1 5/64 (.078) caps and the 1 1/8 on the other studs. $30.00. I feel I need to put in a new joint, but in all reality, I could just change two of the bearing caps on the 7260 joint, right...

My bad, that educated guess should be 1310 to 7260, I'm very sleepy.

Thanks for reply guys. I'm having a bad week. I'm going to pull the joints from both shafts this weekend and take them to a friends local auto parts place. We are going to do the measuring bit and see what we come up with. I think it is a 1310 to a 1330, but we will just do the visual and...

Hey guys, I need help. I asked this same question to Denny's drive shaft and they told me no such animal was made. Here is my plight: 7 1/4 rear trashed in my 67 Barracuda Fastback with 273 engine. I had a excellent 8" Granada rear that bolts right in place (I'm changing to 15" steelies and...

Thanks for reply. I have a set of the 2005 6.29's and they look brand new ($150.00 at swap meet) for 67 Fastback. I just hate that deep back space. I have put new 245/245 rubberon them. I also have 8" Ford Granada rear, but we had to use a 1" spacer (not adapter, with 3" studs) for leaf...

Sorry about that 318, (not BJ).

Looks great BJ. What tire are you using and also are those 2004 and older Bullitts? I know the 2005 and newer have the 6.29 back space where the others have the 5.79 (I think). Are you using any kind of spacer? I'm at work and didn't read complete thread. This may have already been answered. How...

I have both "fish" left and right, I just need the "Barracuda" script emblem. thanks guys for reply.

OK, anybody out there know if the front fender emblem off of a '66 cuda is the same as the '67 ? I just bought an emblem off of Ebay and when it came in, it is the emblem for the tail panel. Too big for the fender! Does anyone have a fender emblem for a 67? All I need to complete my daughters...

bama-a-body, my daughter just started teaching in owens cross roads area. I visit there occasionally. I have a '67 fast back that I hope to complete one day. I have actually given it to my daughter, but she probably won't take posession until I, like,leave this world, but she will get it. I live...

I have the 17" 05 GT wheels (6.29 back spacing, Granada Rear), gives another inch width in rear over old 7 1/4, and the front rotor snout machined down. I also have 1" spacer in rear. The center ford cap was removed and the 3 bar knock off snapped in place. This gives added space for dust cap...

Sorry about the confusion "71. My question is, "Can I just use a master cylinder designed for "manual" disc brakes rather than putting in the booster and creating power brake set up". It would still stop good and have a decent pedal wouldn't it? I know the power brake set it would probably be...

This has been answered a 100 times i'm sure (forgive, cause i'm old) I am swapping brakes to my 67 Cuda from73 Duster. Can i just use the master cylinder reqiured for manual disc brakes? I have a good booster, but wasn't sure of the degree of difficulty. I also have the proportioning block from...