Search results for query: *

I have a block and bore is reading 4.040 is this bore to 40 over pistons ?? Thanks for all the help

Question what is measurement on a 30 over 360 piston ? Is it 4.030 ? Or is the 4.030 the bore size for the piston ???

Yes it have aaw and big. X Cast on ends

I have 2 cranks from 360 4027169 with cfd cast into it and a 3418640 . Are both crank the same or is one better ? I'm planing on building a 78 year block and want the better one of the two

They are all pressed pined , I read a guy had same issues as I have . Could they done this from factory ? To my beleive the motor have never been apart

Motor was in 1 ton truck , four barrel motor, is this motor suspose to have these rods in it or was 2 been replaced ?

I picked up a 85 360 tore it down and notice 6 rods had 2899496 pressed pin and 2rods cylinder 3and5 had 3418645 pressed pins also is this right or have someone been in this block ? Crank number 20277169 , block number 4179930-360-2 , could some one help me , the 6 rods showing they are 340...

I'm running Hughes whiplash 504/515 in my 360 i like it a lot , nice idle and great sound

What should be range of measurement to use this block if it's 30 over , I'll get tool to do bottom and middle reading, block and bores looks in great shape , trying to budget it , but need numbers to work with , thanks

I have a 360 block I used a digital caliper on piston bore , reading I got was 4.035 is this in specs of being 30 over ?? Thanks

Ok thanks , you all helped alot

Sorry for bad spelling ,,, spell check

I picked up a 360 block and crank dispose to be 30 over bore is the piston hole should it be 4.030 when measureing it ? Also is the walls bad it have lines running in it , I can't feel them hand not groves in walls

thanks again all

if everything installed right and still making chatterning could push rods be too short ? i installed factory leanth and called hughes befor buying to see about pushrods for cam, would roller rockers with adjustable pushrods help any ?? thanks for help all

i got my 360 done, it is a 78 model four barrel motor ,im running a hughes whiplash cam 504/515 with matching springs ,locks retainers,and lifters, i installed comp pushrods. the motor have the self adjusting rockers arm with shaft. (factory) . the motor started right up and sound decent other...

yes pistons are stock, stock bottom end, i have read cams with over 500 lift should use rller rockers so ill be getting them, what im trying to do is build a little solid motor with more balls then my 273 that is in it now. motor is around 8.5 to one compression i have read hughes whiplash cams...

78 360 four barrel motor, 596 head casting smog holes pluged off, double roller timing chain , hughes whiplash cam 504 intake / 515 exhaust with 1.5 rockers matching springs,locks,retainers, alum dual plane intake, my trany is 727 with tci breakaway converter, what size carb should i use with...

thanks locomotion , 10236 should be what im looking for

i have a 78 360 with 727 trany , the motor is external balance , i have a tci breakaway stall converter i want to install to this setup, being external balance do i need to change the flex plate or buy weights to weld to converter ,i notice factory converter have a weigh add to it. if i need to...

i have a 68 valiant with a 273, im planing on droping a 360 in its place my question is can i use the 273 motor mounts and brackets on the 360 ? whould i have to buy sertain mounts ?

yes stock gears 7 1/4 for now till i find 8 34 to replace

i have a 78 heavy duty 360 four barrel and 727 trany came out of an rv with 52,000 miles. i drove rv befor pulling motor and run good, i now have motor pulled apart to install new gaskets and paint. motor have the 596 smog heads i have already pluged off the holes. this is going into a 68...

i have a 68 valiant with 273 will the oil pan work on a 78 360 ? i went to jegs and they gave me a pan for 72-89 center sump #555-50272, my car is center sump also, will the one for 72-89 work ? im buying parts for the switch over for this winter and dont want the pan i bought sitting around...

thanka ao much for all the help

ic, thanks , would the 68 273 water pump work on the 80s 360, trying to figer it out so i dont have to change raditor and brackets. would the 273 pullies work on 360 ? , thanks for all the help

would a 68 273 timing cover and water pump work on a 80 360 ??? does any one know ? thanks

thanks alot

i got a 80 model 360 im putting in a 68 valiant what alt brackets ,pulleys and power steering bracket do i need so i dont have to use the a/c compressor , any one have any pictures so i can get the idea of what im looking for ?? will my 273 items work ? and do a 273 and 360 use the same water...

thanks alot guys , helped out alot. .