Search results for query: *

My plastic heater vents are chalky so I’ve gently sanded off the chalk the best I can but it’s impossible to sand into all the crevasses. The paint shop recommended SEM flexible coating paint. Do flexible paints stand up well to heat? The can instructions call for an “appropriate adhesive...

My ashtray was rusty so I dunked it in acid for a bit so the rust has been eliminate (except for the flash rust). Unfortunately the retaining clip didn’t survive. Should I drill out the two bottom rivets to separate it into two pieces before I paint it? The face will be black and the tray will...

My Braces for my 68 Barracuda are bent out of shape and I’d like to know the approximate angles that each end needs to be before I install them. Does anyone have a picture of a picture brace for reference, or the angles they need to be bent to?

I think they’re from a Mopar. They look like rocker trim but they don’t show any road rash.

I have a small damaged area on my dash and I was wondering what would be the best way to fill the hole. The hole is about 1/4” x 1/2”, and 1/8” deep. I thought I would dap on a thin layer of urethane glue, and then mist it with water so it foams, and keep doing that until the spot is level with...

One of lens is cracked on my fender mounted turn signal indicators. Does anyone make repops of the lens or do I have to buy new signal indicators?

Do most members install washers between the hinge and the body’s sheet metal when installing the hinge? Also what is the best way to install the push nuts, and how snug should they be against the hinge? I thought a deep socket might work the best to push on the nut.

A friend of mine is looking for a set of Barracuda Slickback trim. So far he’s not having any luck and he thought a body shop could modify a set of side trim into some Slickback trim. Does anyone have pictures that show the profile of the Slickback trim? Thanks in advance

I've only seen 68 Barracuda trunk trim with the argent center and with the blank trim in the grooves but mine is bare metal. Was there an option without the argent colour and black trim? My car did have the side gills and spears if that mades a difference. I have a piece that is the standard...

Which is a better for blending finishes on today's factory non-metallic finishes: one stage or two stage, or do they have the same finish?

Is there any way to remove old paint from anodized trim without harming the anodized coating?

I have a Barracuda door and I'm trying to determine if it's a 67 or 68. I've read the the vent window assembly mounting brackets and hardware are different from a 68 and 69. Does anyone have any pictures that show the difference?

I have several 69 Barracuda tail bezels that are heavily pitted on the lower surface that is covered by the lens. Are these worth fixing?

I want to take my car to the painters this fall and I would like to have the body on a set of body dollys when I drop it off. Can sub-frame connectors be installed when the body is on the dollys or does the body have to be on the complete suspension?

I have a 69 Barracuda F/B trunk lid that has rust damage to the inside bottom lip. It is in good shape except for that. Is it worthwhile to have a bodyshop weld in a new piece or does it make more sense to buy one that doesn't have rust damage??

I hope to get the old 68 ragtop into the autobody shop this summer and I was wondering if I should get the door striker posts reinforced while it's in there. The posts appear to be in good shape and I don't see any cracks but I understand that the posts are a weakness with the Mopar A-bodies...

'My Classic Car' (2011, episode 18) was about Jay Leno's garage. Jay briefly demonstarted a product that was poured over plated pot metal to restore the finish. Does anyone know what the product is?

Does anyone have a broken convertible latch mechanism for a 67-69 A body? One of my latches is mssing the spring and the small pivot stud.

I have a 68 Barracuda convertible. Are these the correct sillplates or are they from a E body cuda??

I'm trying to find a replacement jack for my 1968 Barracuda and I've been told that there were different tire jacks depending where the car was assembled. My car was assembled at Hamtramch, MI. Does anyone know anything about this? I have seen two different style of bumper jacks and there is a...