Search results for query: *

This is a 489 case with a new 3.73 ring and pinion and crush sleeve eliminator. Is this pattern saying that I need to add a pinion shim to increase the pinion height? If so, I don't think there's any way I can remove the pinion bearing without destroying it. Is it possible to just add a shim...

Does anyone have one of these wire clips that clip onto the pinch weld on the firewall? I believe they may be a 67-68 only type deal. Any help would be appreciated. Thanks.

68 Barracuda. 10" drums on an 8 1/4" rear. New shoes and hardware. E brake disconnected at the adjuster. Brake adjusters threaded as far in as they'll go. The drums are tight on both sides. I can get the drums on but they are tighter than I would ever want them and that is with the hardware...

My house has a drainage ditch in the back yard that runs from east to west. Basically the drainage from a handful of houses to the east runs through my backyard to a 6in drain. My neighbor said he was around when they installed it and apparently it's a 6in drain that has a 90* coupler that...

The plan is to run a belt on the inner groove of the crank for the water pump and alternator. Outer groove of the crank for the compressor and power steering. Problem is that it also runs down the outer groove of the water pump pulley. I have a feeling this is a no go but I wanted to check here...

Installing a set of .007" offset dowels to get the run out alignment in spec and it seems to me like the dowels that shift sst sent me are too long. The side with the cut outs should go into the block right? I installed them that way but there is a good 1/4" gap when I tried putting the...

Do I have these mounted correctly? Not only the orientation of which side of the ears the brackets go on but is the rubber mount itself supposed to be offset from the bracket like that? Seems kind of off to me. Thanks. First pic drivers side. Second pic passenger side.

I noticed the factory lower bearing was toast on my 68 Barracuda floor shift column so I bought one of the bearings from 72blunblu's how to article. https://www.forabodiesonly.com/mopar/ams/how-to-replace-your-lower-column-bearing-better-and-cheaper.66/ The column basically has the main...

I bought this kit from Jegs a while back and just did a test fit. This is a 68 Barracuda with a power steering floor shift column. https://www.jegs.com/i/Borgeson/153/999065/10002/-1 The column installs into the coupler without the shaft needing to be cut but I always thought they needed to be...

Just want to give you guys a warning about Tamco. Let me start off by saying that their products are actually really good for the price. I've been nothing but satisfied with their primers, basecoats and clears. With that said, their customer service is awful. I ordered a dark gray Porsche...

Hey guys, I'm looking for this style valve for a disc brake setup. I know they're sold new but they tend to leak. Would rather just rebuild an original if anyone has one they're willing to part with.

I'm stumped here so I'm hoping one of you guys have ran into this issue before and know what to do. I've got an old 125A Zinsco combo main panel w/meter that I need to replace. The panel is mounted to the outside of my house, just left of the garage door. The feed from the power company comes...

This is a 225 with a Carter BBD, HEI ignition and NOS Mopar distributor. Drove it to work and everything was perfectly fine. Went to drive it home and it would stumble and die once I'd hit about 25mph. Seems to drive fine under that speed. It also idles the way it should in neutral. I can rev...

Where do you guys like to mask when you paint an engine bay to make it look as seamless as possible when you wind up doing the body at a later date?

I bought a hardware kit that comes with a couple of these sleeve nuts. I'm guessing they go on the left and right side of the passenger manifold and screw into a stud but neither one physically fits in the holes. I'd have to drill the holes out a little bit to get them to fit, which has me...

Are all 7 screws that hold the rallye dash bezel to the dash frame the same? It looks like the 3 that go along the bottom side of the bezel are definitely chrome 8x3/4 fillister head screws. FA 4074 C listed in mrg's catalog https://mrgusa.com/pdfs/146-147fillis But are the 4 that screw...

I'm just looking for one of the little rounded square chrome knobs for the heater control. The type with the little hex set screw on the bottom. Thanks.

I sprung for a new 68 Barracuda rallye bezel and am dismantling the old one and at some point whoever worked on it used this white glue that stays slightly malleable to where I was able to peel it off with my fingers but it was strong enough to hold everything in place. Anyone know of a...

I don't know how to photoshop but you'll have to use your imagination. Been kicking around some ideas on how I should paint my cars in the future. Normally I don't like custom but it's been growing on me lately. The idea is for it to be custom but still look like it could be factory. Idea #1...

Hey guys I just bought a woodgrain steering wheel with the horn cap and horn cap retainer. Is there a horn switch or something I need to purchase as well? The car I have has an old crappy aftermarket wheel so I don't have an original horn switch. Is there anything else I need to be able...

Just recently put some seat covers on the rear seat and when I install it, I can only get the seat to fold down to about a 45* angle before the cams hit the brackets that the bolts go through to attach the seat to the car. I took pictures of the brackets so I could get them back on the same...

I have the rubber mounts but I seem to have misplaced the brackets. If anyone has a set of stock brackets, I'm interested. Thanks.

I have the single strap for the 67 but I'm just wondering if the 68 tank can be installed with the single strap and if everything lines up correctly. Thanks.

Hey guys I stupidly bent my bracket when trying to press out the bushings when all I needed was to grip them with a pair of pliers and rip them out. Lesson learned. Anyone have one of these? I don't need anything fancy. A stock one covered in dirt and grime will do. This is for a 71 Duster. Thanks.

*MW99601G - 1964-69 Mopar - Custom Wood Steering Wheel Kit with Barracuda Fish Logo They make them with a couple different horn buttons but I was wondering if anyone had a picture of one of them installed or any idea of their quality? I really like the look of the rim blow wheel but I don't...

I recently moved a bunch of furniture from a couple of rooms in my house and I noticed the baseboards were discolored. So I took them off and they had obviously soaked in a lot of moisture. Turns out all the baseboards along the back of the house and halfway up one of the sides are like that...

I'm in the process of installing the rear defroster and I really don't want to get rid of one of my 6x9 speakers in the back to install it. Do you guys think it would be a bad idea to run longer studs through one of the speakers and just install the blower motor below the speaker? The draw back...

Does anyone have an original proportioning valve for sale? Looking to rebuild an original. Thanks!

I currently own a home in the city but I'm going to be getting married next year and we're planning on buying ourselves a nicer home. I'm looking to possibly move to Auburn California which is like a small city but still very much country. In our price range there are some homes that come with...

Just did a drum to KH disc conversion. Went to bleed the brakes and had multiple problems. The proportioning valve I bought from Summit leaked from the top nut so I tightened it down and it improved things but still couldn't get it to stop leaking all the way. It also leaked where the line...