Search results for query: *

1972 was the transitional year to a new style fill neck (and new tank venting). Seems that repo's are available for 70-71 and 73-75. I'm not sure what makes the 1972 different from the 1973. From pics on this forum and Google, looks like they mount the same way. It appears that mine is...

Got any photos of installed clutch linkage to share? I'd like to compare. I have a converted from auto Duster and it started doing this... (video). I'm concerned that the geometry is off at the stud on the fender, forcing out the spring retainer out.

Looking at Year One to get a new radiator and see that M/T radiators cost ~$45 more than A/T (both 22" and 26"). I'd think that M/T would be cheaper as there are fewer parts. Am I missing something?

Newly installed Innovate Motorsports 3891 DLG-1 Dual Lambda O2 Gauge in my 408 Duster. Notice the lean conditions and the vacuum gauge.

I was told this was an A-body SB z-bar. Is this accurate? The fork connecting rod is curved and the overall length is longer than 7" (maybe 8 or 9"?).

What are the measurements for where this bracket should be installed in the wheel well? The car has been modified to have a 4-speed so I cannot trust the ball stud location. 1972 Duster.

Is it normal to have only 10.6v going to the ballast resistor when the key is on? Battery at 12.1v. When the line is connected to the ballast resistor, it drops to 9.1v and the other side 5.5v. 1970's Electronic ignition. Mix match of several parts on a 1972 Duster.

Anyone install a Street avenger on their small block stroker? I installed a 870 cfm Street Avenger on my 408 and it stumbles horribly. Want to know what modifications others have done to the out-of-the-box carb before I start experimenting with accel pump nozzles and jetting. 408 4spd 3.23

What is this tiny port below the electric choke on the 870 cfm Holley Street Avenger? See attachment.

WTB 1972 Duster taillight lenses or assemblies. All tabs in place and undamaged. Pair.

Anyone use a vintage battery topper on a gel-type Optima battery?

Trunk mounted battery with disconnect switch (4 post). I'd like to run a relay up front to avoid having more hot wires running the length of my car. Where are the best places to slice the relay into? 1972/74/77 wiring.

Why are the tabs on the wrong end? Air cleaner off 1969 440, Carb is a Holley Street Avenger. The slots are at the front of the carb and tabs at the back of the air cleaner assembly.

Dash Masters (owner: Alan Fox) may have gone out of business. That, or it’s a scam. I ordered an A-body dash in Med. Blue at Spring Fling on May 11th. I have not received the dash and am unable to get a hold of Alan anymore. I called him dozens of times over the last few months. We...

BBP Rear Brake Backing Plates 10x2.5" for 8.75. I'm converting my 1972 8.75 to BBP and need the backing plates. Hardware would also be desired but not needed. San Diego, CA

Satin black hood, fender tops, doors, around windows. Is this called the 'performance hood treatment' option? http://www.lhmopars.com/MOPAR_Ads/1971_Plymouth_Duster_ad.jpg How far down the fender on the engine side does the black go and was the black before the body paint?

If starting with a bare roller camshaft 360 block, 1989 casting (4315830), can Magnum parts be used for the roller camshaft, including the cam itself? Spider, tappets, etc. Are they all Magnum interchangeable?

Anyone put Challenger seats into a 1970+ A-body? I have just that but the seats sit too low. Checking if anyone else has and remembers the dimensions of brackets they used (to compare to mine) before I fab my own.

Anyone with Specialty Rallye wheels tried to fit the factory trim ring and center cap? I'm looking at the 15x8 Rallye and Specialty Wheel's response was: "I couldn’t guarantee the fitment from the original equipment to the aftermarket." (rep: Eric Davis)

*NEW* Exhaust wrap by Cool It Thermo Tec - $35 *NEW* Chrome Alternator and dual belt pulley attached by PowerMaster #17509 --$150 *NEW* Holley fuel regulator - $15 Mighty DEMON 650 CFM w/ FBO line kit <500 miles - $440 shipped. See: http://www.forabodiesonly.com/mopar/showthread.php?t=95489...

From searching, it appears that the correct flat black for a 1972 Duster hood is 'organisol' ddl9355 or PPG formula (DCC-9355) but what about the clear coat? This is a textured black, can it be cleared with a flat clear? Anyone cleared their flat black hoods?

Would applying a clear coat over a flat black Duster stripe make the stripe glossy? How can I prevent this if so?

I've been told about a coating that goes over bare/stripped body metal with rust pits that seals the pits before priming. Anyone heard of this?

I switching from a Mighty Demon carb to a Holley Street Avenger. Are the fuel fittings the same?

It looks like all you'd need to do is bolt-in the axles (w/green bearings) with matching brake assemblies and wheels to convert to big bolt pattern, Will the brake line plumbing connect up fine? I'll need 29-spline 1973-76 A-body axles I assume, right? Car: '72 Duster 8 3/4...

The second hand Sure-Grip 8.75 489 rear-end in my Duster only spins one side at the strip, I assume that it is worn out. Since this is the cone-style, I cannot rebuild it so can I buy a new unit to put in the 489 casing?

Apparently the big three had different flat blacks and Chrysler was the flattest. Is there a code or something I can go by to get the correct flat black for my Duster hood?

After stripping the paint, is it now the common practice to use epoxy primer instead of self etching primer? I've heard that you use epoxy on bare metal now so that you can work on the part after stripping.

I have a 408ci running well with the Mighty Demon 650 but want electric choke. I don't like tuning carburetors, I'm at the point where I just want to drive it and not sit with my foot on the pedal for 10+ minutes to warm it up. I've heard negative about Street Avengers in the past. What are...

‘been thinking of replacing my daily driver Camaro with a an old Mopar with a 1990’s 318 to benefit from the EFI and other Magnum design features. Question is, what are the high-cost/problem areas? My plan would be to buy a complete engine/trans off a Magnum truck from the junk yard...