Search results for query: *

Mancini Racing conversion brackets and mounts to put the LA smallblock in a /6 car without changing the K member. Brand new, never used. $100 obo.

I'm moving. I drug this stuff across the country once, and I don't want to again. I sold my Dart, so all of the following needs to go to. -360 LA block Bored .060" over, Hi flow oil pump, speed pro pistons, lunati voodoo cam and lifters, MAGNUM heads, MP valves and springs, Performance Products...

1972 Dodge Dart Swinger, 225ci Slant 6, Automatic, Hurst Promatic 2 shifter. Great cruiser, or perfect base for restoration project. Very little rust, NO HOLES. Fun to drive. Clean title. I have some more pics somewhere, but this is all I can post right now. In Lexington, South...

Heating/AC control unit from a '72 Dart. 90% condition with good heater core, I've also got the compressor, came off a /6 car. all the switches and what not worked when I pulled it on Saturday. I'll sell it, but I'd be happy to trade it all for a V-8 steering linkage needed for a /6 to 8...

I know this as been asked already and I've read all the responses, but I just need confirmation to go along with what I think I need to do next... On my 360 build, I installed a new brass bushing and went to install the oil pump drive shaft. It didn't drop in, so I gave a few taps with a...

I managed to put my hands on a complete 8 3/4 rear for my Dart, Great shape, 2881489 casting number, Moser axles, great deal. It's supposedly a B-Body rear and by my best measurements, it is. The questions are: 1. What am I going to have to do/have done to fit this under my '72? 2. Since...

So, the threads on my steering shaft that hold the main nut have been gummed up beyond repair. I figured that I would just get a threading die and cut some new threads. Until I found out that a die that big is $40. Anybody got any ideas, or want to loan me a die for a minimal fee ?

Anybody have any pointers on what will make the install smoother? I've already read great things about the hardware and install itself, but I'm wondering if there's any tips that aren't listed on the accompanying paperwork. Thanks!

Here's the deal.. '72 Dart Instrument cluster issue -Copper runs are clean, bulb sockets are clean, bulbs are good, Voltage Reg is new, all ohm and continuity checks passed. -Main dash harness connector is clean and tight, continuity from connector ends to farthest end of copper run is...

Anybody recommend or have a really good experience with a shift kit for a 904? I'm putting a 904 behind my .060 over 360 and looking for a streetable ride with some punch. Thoughts?

Temples Auto Salvage in Batesburg-Leesville, SC. DO NOT GO HERE. While it is loaded with a boatload of Mopar parts cars, the assclown running it is apparently not in the business of making money. I called him on looking to pick up a steering column and engine brackets and he says he's got...

My brother has a 62 Chrysler Newport, with a tortion front end setup. Apparently, the control arm screws into the bar, and his threads are chewed up. The 'Zone and others can't help him find a replacement. Anyone know of something that would work from another Mopar?

My brother just picked up a '62 Newport with a 361. He asked me if a B/RB factory intake would fit on the 361 engine. Since I'm not sure, I'm going to pass it on to the experts..... Anybody?

Worked when I pulled it. Great shape, no cracks. $40

Anybody want this? Good shape, no converter. $50

Polished headers, fits small block V-8's Some dents and dings, but no holes. $100obo

Autometer Sportcomp Silver series tach Worked fine when my buddy had it in his Cobra. He gave it to me to square a debt. I was going to put it in the Swinger, but it's a little too "Alarm clockish" for me. $100 or best offer.

318 Vatted, fluxed, bored .030 with new pistons and cam bearings installed. Started to build, but sold the car it was for. Kept covered in garage, ready to build on. Would like to get at least $400, but will entertain trades for '72 Dart parts or a complete 727. Also includes set of factory...

The "welch" plug that goes into the back of the 360 block behind the cam. It comes with a full freeze plug kit, but the one that came with mine got lost, and one that a fellow FABO member sent me for free, the Post Office delivered... in an empty envelope. I can't find one around here anywhere...

Will a 8 3/4 rear from an E body ('70 Barracuda) fit under an A body ('72 Dart)? The only reason I ask is because I might be able to get my hands on a dirt cheap 8 3/4, but I don't want to drive 3 1/2 hours to Georgia to get it and find out it won't fit.

I got a 7 1/4 rear on my Dart which I change the leaking pinion seal on. Followed the directions in the service manual, "pinging" with a spring punch alignment marks where the pinion bolt and nut could be realigned. Replaced the seal, reset the nut to the mark, plus 1/8th of a turn per the...

Old voltage regulator: Key ON: Fuel reads half Temp reads 120 Engine ON: Fuel and Temp Peg all the way to right New voltage regulator: Key ON: Fuel reads empty Temp reads -120 Enigne ON: SAME. Tested gauges and sending units, both check good. Dash ground good, connections good. WTF?:angry7:

I got this video sent to me in an email from one of my buddies back in AZ, it's from Jay Leno's Garage show, which I've never watched because I can't stand Leno, but it does showcase some amazing new technology that probably will directly affect our hobby. Also, just like our cars and many of...

Can anyone tell me what exactly the instrument cluster voltage regulator is supposed to do? With the old one in, my temp and fuel gauge peg to the right, with the new one, their both dead sticks. Cluster ground is good, can't figure it out.

So, I bought this Dart from this nice kid who I'm now figuring out knows as much about auto electrical systems as my cat. Aside from the gremlins running through my car's electrical system, I've decided to tackle the dash first... He bought a instrument cluster voltage regulator that plugs into...

So I just bought a '72 Swinger Special that has the 225 /6 in it. It's a runner until I finish my Magnum headed 360 for it. The 6 runs ok, but there's a lot of bare vacuum connections in the engine bay. Not to mention that I found the vac canister in a shoebox in the trunk..... Can anyone...

Can anybody tell me which rear end is likely in a 72 dart special with the /6? Looking at one on Craigslist and guy didnt list and I can't find any info online, like to know before I contact. Thanks!

Due to the lack of space, time, and dispensible income, not to mention an inbound rugrat, this project has to go, and everything else with it. 1969 Dart GT, California built, Arizona kept, been in South Carolina in garage for three years. Only rust is in the low rear quarters. -No major body...

I just wanted everybody here at FABO to know that 6Dart9 is a good guy8) and the USPS is a pack of chumps.:thebirdm: Thank you.

So I bought a freeze plug kit from Summit for my 360 that's getting built and I realized that the welch plug (The dish shaped one, at the back of the camshaft) that came with the kit has gone awol. After 2 hours of tearing the garage apart looking for it, I have run out of options. The local...