Search results for query: *

http://www.forabodiesonly.com/mopar/showthread.php?t=307984&highlight=frame+rails check out this members rails for sale-- use them as a guide as to what yours should look like, they look to be prime pieces of metal. i do not have any affiliation with this seller-- i just think he does an...

If your frame rail is that bad in that spot-- I would check the rest of the rails-- both sides- then buy a nice used piece from a member on FABO or source one locally & weld in a replacement section or rail depending the condition of your ride. that is so rusted it pulled the captured nut...

also tap that stuck bolt repeatedly with a hammer-- better to use 2 ball pein hammers-- place one on top of the bolt-- then hit the other side of it-- that way you do not round off the bolt anymore. Lawrence

FUN!! hope it gets you the times you want ,Lawrence

thanks for the great detail-- this needs to be put in the tech section ,Lawrence

lengths are different between bb & sb, never had a slant with one so do not know ,Lawrence

I'll throw a wrench I once placed a 360 in a 64 chevelle just to visualize the mounting problems-- needless to say it didn't happen. much younger & energetic at the time. Lawrence

is there a throttle stop? is the carb opening all the way?

no idea on times-- but can I test drive it? Lawrence

I didn't read most of rumble's post-- but I'm positive his advice is sound . You need to assist us with more detailed info-- you don't know what gears you have not sure about the engine-- but you want to go faster. That is one vague & expensive statement. You need to find out what your car...

need? depends on what your are building, if you have the other side --might as well save it-- I sold a pair from a 74 duster for $50 shipped --so they are not valuable. not sure what your building-- did n't you have a toad car at one time ? Lawrence

nice looking car-- you going to paint the tractor to match? you picture reminds me of the state fair & the FFA re-building grandpa's tractor, some of them are very nicely done!! as for performance, these guys will set you straight-- the biggest question is-- what do you want it to do...

that's probably a good price-- but 360 heads on a 318 lower compression--- just food for thought-- bigger combustion chambers. Lawrence

here is what i have in my garage-- 2 different sized bolts. Lawrence

rebuilt? that is the $100 question-- does he have receipts? I have heard of people just degreasing engines & painting calling them rebuilt. so be wary of re-built engines. Lawrence

and the factory gauge does not tell you temp-- you need an actual gauge with degree markings or a heat gun to tell what the actual temp is. Read the above posters comments & explain the detail of your cooling system, thanks Lawrence

front pump of the tranny? Are you fluid levels all good? --does the car work ok--- Lawrence

k frames 62-66 --will not interchange with later years 67-- 1st year new design 68-72 pretty much all the same-- (biscuit mounts) 73-76 pretty much all the same-- (spool mounts) 67-76 will all fit the cars--- but swapping in has unique parts . If you want to swap to a v-8 by switch...

tap it & pull the tap & tube out. Lawrence

could be hardened pieces of old valve cover gasket. Lawrence

not sure-- but if this car was running good b-4 tune-up-- can you return it to that state? you need to phone a friend before you waste $$$ or ruin a running car---- as you can tell by the varied responses on here that a correct diagnosis is in order-- it could be that the new parts just...

try disconnecting the booster-- plug the line & see what happens--- try it before the check valve & after the check valve---- if it works fine -- you then have narrowed your problem down, Lawrence

what the others said -- plus if you are not spinning in the higher rpm range-- it just is not worth the bigger valves. Lawrence

69 darts are cool cars---- 1. Does the 318 parts are easily available. I know that this engine is common in the 1990's dodge pick-up but is the parts can retrofit in the 69 dart. And same question for the slant6 225 if I stay with this engine Not sure what your question is?? if you like the...