Search results for query: *

I need to buy a new one of these..anyone know where I can buy one ..it goes in the kick down link..thanks all..j

Im looking for info on a 96 dodge pickup 1/2 ton I think auto trans with 360 motor..anyone know what autotrans it would most likely come with.and any info on it,..tx...j

Have one laying around with clutch style s/g..needs bearings ..what can I expect to pay to have new bearings put in..tx,j

anyone using arp bolts on their press plate and know what their recommended torque is?.tx..j

I want to find an automatic 727 and id like to get the best one possible..if I were doing a 8 cyl dart like 67 to 69 which trans would best fit the application.. one from a small block truck or a early or late one from a van or a car or what ..any of you automatic gurus have a best..thanks ..j

I picked a 489 case 323 yesterday but the yoke in it is done..needs a new one..i dont know anything about the 489 case.my question is how do i change the yoke .do i have to worry about the compression tube in it or is it a direct take out old bolt in new and torque it ..any help appreciated .tx.j

fel pro offers 2 diff gaskets for the 8 3/4.one book says is steel and one says foam.using green bearings which gasket to use and where..is there a schematic somewhere that shows gasket placement ..thanks..j

So lets talk shop here..For the person that has never rebuilt a third member or had one rebuilt, what is one looking at in cost providing a reliable shop is found.what is the cost for parts bearings cups and seals.then what is the cost for gear set if a set is needed and then what is the normal...

So after putting in a 323 sg a body rear in the duster last w/e i finally got a chance to drive it...NOISEY is the word..id call the noise typical stick shift noise..not a bearing whine, like an idler bearing but a definate constant whine whether you are on the gas or coasting...the noise goes...

Can someone that has the knowledge share some light on a trans with the numbers in the photo..any and all help appreciated...j

im looking to get a d/s cut this week..id like to have a slipyoke in my hands so i can test fit it and make sure im happy with it before i take it all to get cut and assembled. if some one has a part number for a slip for a " A body 833 four speed preferably spicer or neapco,it would be really...

just about have my 8 3/4 ready to go in,but would like to get the shaft shortened..went over the charts for length and found way to many irregularities to trust it ...does anyone know the correct length to make it ..using 360 a833 and 8 3/4..73 duster ..any and all help appreciated please..tx..j

i want to run 10 x 2.5 brakes .with my 8 3/4 is anyone else running this combo..is there any issues with this combo..tx..j

NEED HELP..Son wants to put on wheels[73 duster] and i want to go from a 8 1/4 to a 8 3/4 first..its a body 8 3/4 ,so it has sbp axles..i have a set of 10 x 2.5 backing plates from a truck..if i buy axles made for these brakes dimensions.do i have to reconsider the backspace on the new wheels...

Went out to find SET OF 10 X 2.5 BRAKEs today at the local yard im trying to get my 8 3/4 set up to put in the car...took me three different 8 1/4 rear ends to get a set of back plates because the bolt [pin was broken on two rearends..couldnt remove the bar to slide in the axles so i could...

iv had this unit for over twenty years and dont know anything about it..can anybody shed some light on it..i was going to make a new pin for it and never did..i think its for chevrolet but im not sure..thank you all..j

iv got a chance to buy a dana from a 74 duster..supposedly it is a original rear from and installed by mopar...has anyone heard of mopar doing this in an a body..how are these rears..thanks for the help..

does anyone have the pinion seal number for the 8 3/4 axle 741 case 1 3/8 shaft they would like to share with me.im using national seals .thanks all..j

will a person well versed on these explain to me what would not let a axel turn why can i hold the axels from turning whil i turn the yoke....also what makes a housing unusable..other than the obvious like being bent...any help please..jim

help..im not a rear end person..i just picked up a b body 8 3/4 and the person i bot it from says it is good..yet when i turn the yoke,neither wheel turns..i can hold both from turning..open diff[can see spider gears]and a 3.55 ihave in the garage is the same way...can one of you diff experts...

A set of these rods came in a box of mopar goodies i bought ..i cant seem to be able to match these with anything they dont look like a body...then i also have a three speed linkage also ..does any one k now what these are from tx..j

i want to do this swap...is it a direct bolt in..does the 727 with a 360 fit without any body modifications..tx..j

I found a real nice pair of 11 x 2.5 plates with all the hardware and riveted shoes..pulled the cover on the 8 1/4 theywere on removed the thrust rod bolt and they are mine...found a nice 10 x 2.5 pair on a new yorker 8 1/4 rear and pulled the cover went to remove the bolt in the thrust rod and...

I am lookimg for spicer u joints and prolly a new yoke for the 3rd member...who has the best prices today..tx ..j

There is a number on this pressure plate MF 365 ..how does mopar do there numbers on plates and the disc is cd3269e..are these mopar or aftermarket???any help please...also, the flywheel #2264598..any body have any clues..tx..j

i ran into a van today and looked at it has an 8.25 rear..whats the dims on springs distance and can it be verted to 'a' body..it was 3.21 axle...j

im looking to put on a newer slip yoke when i redo my dr/sh i see a plethora of them at the local pick n pull..does any slip yoke i pick that came from a trq flite work on my 73 a833 shaft..tx..j

I got into checking today...i was pleasantly surprised at how close things were right off..i expected .015 or maybe as much as .03 when i put in a pair of 495 pins into the bell and cinched things up then checked it was .001tir from top to bottom and .0075 from side to side .this means,the...

WE talked about doing it and i said id build a tool to check alignment with..well its a go and done..only prob is i dont know how to post the pics i took here...if any one is interested in seeing them send me pm and ill send them to you...or if someone wants to put them on fabo ill send them to...

does anyone have the large diameter dimension for a clutch alignment tool..id like to make one today,...thanks ..jim