Search results for query: *

The cam. Voodoo Solid Roller Cam - Chrysler 273-360 273/279 - Lunati Power The rest of it. 1968, 340, balanced with forged stock replacement pistons. X heads with some moderate cleanup and port work. Factory cast iron intake and HP exhaust manifolds, both unmodified Factory 625 AVS, unmodified...

Pulled the valve covers to have a look and this is what I found. Have not measured the lash yet but the engine sounded fine and nothing felt loose. Just the noise of a solid roller valve train. These are for: #1: E #3: I #2: E & I What to check and what to look for? Opinions?

I need to do a little valve train geometry correction. The roller on the rocker is a little far out on the valve for my liking at full lift. Right now my shafts are shimmed with a set of what looks like a tapered, curved washer. These move the shaft towards the center of the engine and...

In the process of cleaning I broke one top ring on one of my pistons. (I disassembled everything for cleaning, bearing replacement, cam and lifter replacement, oil pump, gaskets.) Cylinders were fine, I didn't have any issues with "smoking" or oil consumption before I pulled it apart...

Ok, a quick question. (Small Block) My old cam (Crower Solid Roller) #2,3,4 journals were approximately 3/4" wide. #2 and 3 journals were fully grooved in the center. My new cam (Lunati Solid Roller) #2,3,4 journals are approximately 9/16" wide. #2 and 3 journals have oiling holes. I...

This is what I am replacing. It worked very well and sounded great. I have the compression (11+), heads, Victor 340 intake, Holley 800 dp, 4 speed, 3.91 gears, TTI 2.5" exhaust with "X" pipe and 26" tire so support it. But I also have the 340 exhaust manifolds back on (but we can ignore...

Lunati Solid roller lifter question. Do the standard Lunati solid roller lifters require grinding to clear the link bar? (I called Lunati and they didn't know..... ) P/N: 72420LUN Vertical Bar Roller Lifters - Mopar 318-360 Qty 16 The bigger question. I am looking for a premium solid...

I didn't want to hijack this thread...... http://www.forabodiesonly.com/mopar/showthread.php?t=168963 What I am looking for is a quality, solid roller that does not need grinding of the lifter valley. My old lifters looked just like the Comp 828's but had an inboard vertical bar...

Who is "THE" custom cam guy? Im at the point where I need some real experienced advise for my cam selection. Im just about positive it will need to be a custom grind. The basics: 340 4 Speed 3.91 gearing X heads (ported and have supported consistent high 11s) Compression is in the mid 11s...

Actual compression of a 68, 340? I know the advertised number but I have seen posts on here that said when the math was actually done it was usually a bit off. Just curious. Thanks.

So…… After having my car sit for 2 years because I haven't wanted to de-tune my original 340 (12.1 compression, solid roll cam, Holley 800DP, Victor 340) I have reached a decision. Well, the decision was made for me. I just got a 60,000 mile, 1968, 318 that is complete (carb to pan with...

Crank end play. So I was changing the lower pulley on my 340 to the new one for AC and without a doubt my endplay is out of spec. I would say (using my eyeball gauge) that it is at lease .10+. The hard life of 8000rpm up shifts and a 4 speed I guess. The engine is coming out anyway...

Will my stock valve covers work? 68 340 Harland Sharp valve train, .550 lift solid roller.... I just set them on the engine and I'm not thinking they will....

Opinion in these roller lifters? 1 month ago Crower told me they were out of stock on my lifters and should have them soon.... Today they told me it would be another month and a half. I was looking at these from Summit... What do you know about them? Lunati 72420LUN - Lunati Vertical...

What solid roller lifters are you guys running? As you may or may not know my car has been down because a couple of my lifters just simply wore out (21 years old, lol). High lift cam and high spring pressure over time... My old lifters were Crane that I can't get anymore. I need...

Help. Identify this Solid Roller Lifter. I need a new set and can't remember what they are.

My cam is dead.... Recommendations? This is what I have now... Crower Street Roller (Solid) This is the 1989 version, Yes it has been in there that long :) ... #31406 (lobe center 112, Adv dur 290 294, lift .550 .555, RPM range 3200 to 7200) The new Crower Street Roller (Solid)...

What's the big deal about a roller 340. My 340 has a solid roller cam (Crower). People have told me it is not easy to make a 340 roller. Mine was installed by the previous owner. Question 2 is about my heads. I know my car has the original engine and was told my heads were the stock heads...

As some of you know I have a 68, 340 Formula S 4 Speed. I am returning the engine compartment to stock. I will be removing my large roller cam (won’t list the specs because it won’t work with my new combo). What I have to work with is a 1968 340 (going to stay with this) Fully balanced...

I have a 68 Formula S 340, 4 speed with 3.91 rear. Engine mods are..... Ported X heads, balanced, 11.5 compression, Edelbrock Victor 340 intake, Holley 750 puddle dumper, Crower Street Roller (#31406 lobe center 112?, advertised duration i&e 290-294, duration @ .050” 251-256, lift .550-.555.)...