Search results for query: *

Where can I find info on this car I picked it up cheap today thanks for any information.

Can anyone show me how to use the Delphi crimpers? We bought them from American autowire I cannot find nothing on YouTube any help would be appreciate. KB9GIB thanks

We are putting in Holley sniper system. looking for where you guys hide your ignition box & ignition coil? I was thinking maybe inside the car? If you have any pictures would be helpful. Thanks in advance. KB9GIB

I’m needing some thoughts on EFI. my son is going EFI on his 340 Demon 20 over J heads small cam. If you where to buy today would you go (Fitech) or (Holley sniper)? Holley is about $400 higher if I looked at it right. Thanks in advance for your input.KB9GIB southern Illinois

My son has a 1970 318 in his demon. we have a set of 302 heads on it I think the intake is elder LD4B, elder 650 carb, only number I find on the cam is EDEL 955836, I can’t find any spec on it with 323 gears. This thing starts runs out good but will not get out of its own way. So just looking...

Can someone tell me on a 340 bearing clearances stock crank & rods turned 20 using clevite P77 bearings what should the clearance be rod and mains. Thanks for any information in advance. KB9GIB

Need advice, 340 motor been bored.20over KB pistons just a street car what would you guys that are motor builders (Gap the rings) car will be fuel injected. Thanks in advance KB9GIB

Thanks

Need some information putting my son’s 340 together do we want bearings with the (dole holes?) H-P-? Style bearings. I’m lost on the dole hole and the type of bearings as the H bearing are P bearing. Thanks for your help in advance. KB9GIB

Anyone know where to find (Bucket seat track studs?) I was thinking a carriage bolt but they look a bit different thanks in advance. KB9GIB southern Illinois

My son has 72 A body seats the tracks are missing the locking leaver’s. on the inboard tracks one side has locking notches but the other side is smooth inside. My question is can you get the inter locking lever? And why is there a difference between the two enter track locking mechanism? I...

I have had no luck on vinyl trim clips for my son’s 72 Demon. Can anyone tell me on 71 a body demon/duster did they use the bolt style clips? And if they did is there access from inside the car to put the nuts on? Thanks for all information in advance KB9GIB

I’m looking for some 72 A Body (Demon) vinyl top trim (clips) I have call every dealer that sells clips and I can’t seem to get the right ones. the one on the left is what they say will work but they are to narrow. The one on the right is a original clip. Any help would be appreciated. Thanks...

How does the Deck lid Dart emblem attach on a 72 Demon? Does it use push in barrows are 3M tape? The emblem has the push pins. Thanks KB9GIB sorry for multiple pictures

Can anyone tell me if the 72 demon rear tail light bezel are just bare metal? On the back side. Thanks KB9GIB

Need some information my son is adding a vinyl top. we ordered some plastic clips but they are to small. I seen where some say they get some clips that have metal screws can someone point me in the right direction maybe a part number and source for them. Thanks in advance KB9GIB Anna Illinois

Anyone with a 72 Demon can tell me what chrome pieces for the front windshield? I think it’s the ones on the bottom. Thanks KB9GIB

Happy Thanksgiving. KB9GIB

Need some information. I looked on the forum on this. They say the vinyl drip rail is wider than non vinyl drip rail? does anyone have a measurement on vinyl drip rail trim. the ones I have came off a 1/2 vinyl top car. and someone mentioned removing something by the front windshield if it...

Anyone tell me on a 72 Demon pop out glass seal does it set on the body are set inside the quarter panel pitchers would be helpful. Thanks in advance KB9GIB

What can I use to cover a freshly painted car sheets are not big enough. thanks for any information KB9GIB

We are looking for a 72 wood grain center dash bezel Like this style. Thanks KB9GIB

Can someone tell me how the wood grain on the a Body glovebox and dash fasten’s to it? My son wants to put it on his 72 Demon. Thanks KB9GIB

Anyone tell what body style this motor came out of? Hemissdart. Was asking about vin Incase he didn’t see my other post. Thanks for any information. KB9GIB

Hello and thanks in advance for any information. Son is building a 340 the motor we have doesn’t have no internals. so we was thinking of doing a stroker the block needs 30 over bore. This will be 90% cruising car. so with out braking the bank what kit (brand) would you go with? I think you...

Any idea on aftermarket air and heat on 72 Demon? was a factory air car. was going to use classic air but it’s just for none air cars any help and photos would help thanks in advance. KB9GIB

Can someone tell me are 73/74 Duster doors the same as 72 demon/duster doors. Thanks in advance

Is a 71 Dart/Demon fender the same as a 72 Dart/Demon fender other than the marker light? And is fitment the same with both years? And is it possible to fill in the marker light? And how does the (AMD) fenders fit? Thanks for any help KB9GIB

Hello, can someone show me some pictures of a trunk (Seam sealer locations) thanks for all your help. KB9GIB

1972 Dodge Demon. Can someone tell me if right and left door hinges are the same. Are they right and left side different. I have looked for the over size pins also but can’t find them. All help appreciate in advance. Thanks KB9GIB southern Illinois