Search results for query: *

My 67 fastback is up for sale. I've retired and the car needs a new home, in the last 3 years its been out of the garage very little mostly shows and cruises. In the seven years I've owned it I may have put 500 miles on it.Its a fully built 440 with a 727 trans and Dana 60 differential. the car...

I hear some of you guys are running E-85 fuel. Its readily availble here everywhere! What mods need to be done to use it? Will it work with 12.5 to 1 compression. Help an old dog understand!:?

Thought I'd post a few new pic's. Been a long time and will soon be updated my photo gallery. I finally installed my Snow Performance water methanol injection system , with the new fuel cell and isolated the trunk from the passenger compartment. Also a pic of the fine work our Leanna did on my...

Anyone decode my engine block casting number. The number is 2536480-6 Its a 440, I think maybe a 6 pac Anyone?

Whats with every picture I look at on this site, including members photo galleries, a Ford swap your ride sales event popup hits the bottom of the picture? Anyone???

I would like any input from someone who has used or using a Milodon gear drive unit on their big block. I'm considering adding one, mostly for looks and sound. Any thing special for install, looks like its a bolt on and would look great with my CSR water pump.

Ok guys, I purchased the Milodon external oil pick up system. Pump, hose, pick up, not cheap. I thought I could install the pick up into te Milodon oil pan I have, but long story short, I cant, so I need to buy a $255 dollar oil pan which pushes the cost of this whole thing over $600 for parts...

I love Mopars but the worst designed part they ever installed on an a body was the bulkhead connector. I'm constantly loosing connections, tightening connections! Does anyone make a suitable replacement? Help!

I decided to replace the front door glass felts, you know the one on the front of the glass tats slides up and down in the vent window rail, and the one on the rear of the glass. Well I ordered the parts from RT Specialties in PA the first part of April. Took me 3 weeks and numerous calls after...

I have a 850 Quickfuel carb. Its running extremely rich. I mean if its running in the garage for any time even with both doors open your eyes begin to burn. It has no adjusment with the mixture screws. Float levels are correct, secondary throttle plates are shut. Could the power valve be blowin...

I have a 67 fastback and the front door window mechanisims need some work. First thing I noticed the is no felt in the vent window track for the door window glass to slide in. I looked at the other door and there is a felt liner but its sliding up and down with the glass. Is it supposed to do...

The passenger side front window on my 67 opperation suddenly works terrible. I took the door panel off and found that the felt thats on the front of the glass was laying in the bottom of the door, the one that slides up in to the front channel buy the vent window. I can't figure out how it...

I sent my neww manifold and valve covers to our CudaChic and WOW!!! What a great job!! The parts were coated alien silver over ink black and the clear coated. The pictures barely do the parts justice. In the sun they just pop. Any you guys contimplating powder coating, I highly recomend their...

Ok guys, Both my front windows are in serious need of some tlc. Where can I find new window felts, and regulator rollers?

I'm in need of the right vent window upper seal. Its the triangular piece that screws to the top of the vent window frame that the upper front corner of the door glass slides into. Here is a picture of the left side, I need the right side.

I just purchsed a new intake and was inquiring about powder coat and another member suggested clear coat. I thinks I would prefer that but dont know what to use that wouldnt be a maintance issue. Any suggestions?

I currently have a 12.5 to 1, 440ci, eddy rpm heads, with a quickfuel 850 double pumper and a weiand team g manifold. I need to replace the manifold, seems the previous owner installed this manifold made for a dominator, and installed an adaptor to put the carb on. Im convinced this manifold...

I currently have a big block with 12.5 to 1 compression and am finding it harder to find racing fuel. Snow Performance claims their system will boost octane of pump gas up to 116. Does anyone have any experience with this system, does it work? The $500 bucks the system costs would sure beat the...

Well I finally have gotten around to installing the Autometer gauges into the dash of my 67, been at it for 2 days and this is how far I've gotten. The gauges are mounted, what a chore! Not much left of the back of the instrument panel, but I think the new look is going to be killer. Stll have...

I have a 12.5 to 1 comp 440 with full MSD and eddy heads. I just installed new plugs (a real pain in the a$$) and set the gap at .045 is that gap ok? Engine now seem to run very rough until it warms up. Any input.

I'm going to be installing a new fuel gauge and needed a new fuel cell with a sending unit so I purchased one just like the one I am using now but with a sending unit. My question is, someone, here, posted a remark a couple days ago about modern fuels eating up the foam,. Is this a problem...

I took a 2 hour drive (1 way) today to exchange some gauges I purchased from Summit. If you ever get a chance to go into one of their outlet do it. WHAT a candy store for gearheads. Can you picture 20 plus intakes, half dozen blowers, 40 carbs, 20 different nitrous systems, and the list goes on...

Is it possible or even feasable to install a gauge sending unit into a fuel cell that has foam and never had a sending unit? Or should I just buy another cell with the unit installed? The cost difference between buying a new cell vrs buying a sending unit is about $80, in your opinions is it...

I'm in the process of ordering all new Auto Meter Phantom gauges for my cuda. What I need some input on is which to go with mechanical or electric. I'm leaning toward electric, is there any advantage to mechanical other than they are less expensive?

I'm thinking of removing the factory speedo and guage cluster in my 67 Barracuda and replacing them with a 5" electric speedo and tach from Auto meter using the existing bezel. Has anyone done this and if so how about a picture or two and a brief discription of what you had to do? Also thought...

For the past few years I've been purchasing parts from both of these companys. They sell the same thing and usually they're very close on price. I needed an assortment of accelerator pump nozzels to tune my 4150. Summit $4.95ea Jegs $11.95ea WTF? Why such a difference in part prices. Where do...

Hey guys, I'm in need of front license plate bracket for my 1967 Barracuda. Needs to be in good condition. Anyone have one to sell?

What is Generation Y? Hmm, I've always wondered this myself. Now I know. _The Silent generation, people born before 1946. The Baby Boomers, people born between 1946 and 1959. Generation X, people born between 1960 and 1979. Generation Y, people born between 1980 and 1995. Why do we call the...

Need you guys suggestions. I have 30 over 440, 12.5 to 1, reworked eddy rpm heads, team G intake, quick fuel 850 carb,2" primary tube headers, 4500 stall converter, 456 gears solid lifter cam, H&S roller rockers (see cam specs) Problem engine runs great mid and high range, off idle I have to...

Everyone has a story! I'll share mine. I went to work at a Plymouth dealership in 1967, fresh out of high school (giving away my age). The dealership sent me to every school Chrysler had available and by 68 I was a line mechanic specializing in engine, transmission and differential repairs...